EWM Phoenix 355 Progress puls MM TKM Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 128

background image

Design and function

MIG/MAG welding

099-005403-EW501

18.08.2016

73

5.3.14 Standard MIG/MAG torch

The MIG welding torch trigger is essentially used to start and stop the welding process.

Operating elements

Functions

Torch trigger

• Start/stop welding

Other functions are also possible by tapping the torch trigger, depending on the machine type
and control configuration

> see 5.10 chapter

:

•  Change over between welding programs (P8).
•  Program selection before starting welding (P17).
•  Change over between pulse and standard welding in the special latched operating mode.
•  Switching between wire feed units in dual operation mode (P10).

5.3.15 MIG/MAG special-torches

Function specifications and more indepth information can be found in the operating manual for
the relevant welding torch!

5.3.15.1 Program- and Up / down operation

Figure 5-55

Item Symbol

Description

0

1

Welding torch function changeover switch (special welding torch required)

---- Changing over programs or JOBs

---- Infinite adjustment of welding performance.

5.3.15.2 Switching between Push/Pull and intermediate drive

WARNING

Do not carry out any unauthorised repairs or modifications!
To avoid injury and equipment damage, the unit must only be repaired or modified by
specialist, skilled persons!
The warranty becomes null and void in the event of unauthorised interference.

• Appoint only skilled persons for repair work (trained service personnel)!

Test!
Before re-commissioning, it is essential that an "inspection and test during operation" is carried
out conforming to IEC / DIN EN 60974-4 "Arc welding devices - inspection and testing during
operation"!
• For detailed instructions, please see the standard operating instructions for the welding

machine.

The plugs are located directly on the M3.7x printed circuit board.

Plug

Function

on X24

Operation with Push/Pull welding torch (factory setting)

on X23

Operation with intermediate drive

«
...
71
72
73
74
75
...
»

Содержание Phoenix 355 Progress puls MM TKM

































































































































Отзывы:

Нет отзывов

Похожие инструкции для Phoenix 355 Progress puls MM TKM

Бренд: Happ Страницы: 52

Бренд: FAAC Страницы: 4

Бренд: EAW Страницы: 2

Бренд: EAW Страницы: 20

Бренд: Yamaha Страницы: 67

Бренд: Yealink Страницы: 8

Passport Conference 2 Series

Бренд: Fender Страницы: 20

Бренд: Dakota Alert Страницы: 18

UTILITY UTAC13-0

Бренд: WIA Страницы: 8

QC804-261-1 NVR

Бренд: Q-See Страницы: 11

Бренд: Miller Electric Страницы: 35

Dead Level Series

Бренд: Watts Страницы: 24

Бренд: Fender Страницы: 14

CARPOWER CRB-130SET

Бренд: Monacor Страницы: 2

Бренд: Salto Страницы: 4

MarCell MAR-A-500

Бренд: Sensored Life Страницы: 2

Бренд: Omega Страницы: 2

Бренд: KBSOUND Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды