EWM Phoenix 355 Progress puls MM TKM Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 128

background image

Design and function

Machine configuration menu

099-005403-EW501

18.08.2016

103

Predefined absolute value for relative programs (P21)

Start program (P

START

), down-slope program (P

B

) and end program (P

END

) can be set relative to the main

program (P

A

) or in an absolute manner, as desired.

Function active (P21 = 1)

• Absolute parameter setting

Function inactive (P21 = 0)

• Relative parameter setting (ex factory)

Electronic gas flow control, type (P22)

Active only in machines with integrated gas flow control (option ex works).
Adjustment may only be carried out by authorised service personnel (basic setting = 1).

Program settings for relative programs (P23)

The start, down-slope and end program relative programs can be set individually or combined for the P0-
P15 operating points. When choosing the combined setting, in contrast to the individual setting, the
parameter values are saved in the JOB With the individual setting, the parameter values are identical for
all JOBs (except for special JOBs SP1,SP2 and SP3).

Correction or nominal voltage display (P24)

When setting the arc correction using the right-hand rotary knob the display will either show the correction
v- 9.9 V (ex works) or the absolute nominal voltage.

5.11 Machine configuration menu

5.11.1 Selecting, changing and saving parameters

ENTER (Enter the menu)
• Switch off the machine at the main switch.
• Press and hold the "welding parameters" or "choke effect" (drive 4X LP) push-button and

switch the machine on again at the same time.

NAVIGATION (Navigate the menu)
• Select parameters by turning the "welding parameter setting" rotary knob.
• Set or change parameters by turning the "arc length correction/select welding program" rotary

knob.

EXIT (Exit the menu)
• Press the "parameter selection right" push-button (switch machine off and on again).

«
...
101
102
103
104
105
...
»

Содержание Phoenix 355 Progress puls MM TKM

































































































































Отзывы:

Нет отзывов

Похожие инструкции для Phoenix 355 Progress puls MM TKM

Бренд: GE Страницы: 36

Бренд: Handicare Страницы: 32

Бренд: Neets Страницы: 16

Бренд: Eaton Страницы: 68

Бренд: Eastwood Страницы: 16

Бренд: Eastwood Страницы: 16

Simply Cinema ESC300

Бренд: JBL Страницы: 10

Бренд: JBL Страницы: 12

Бренд: JBL Страницы: 2

Бренд: K-array Страницы: 20

Бренд: Tracer Страницы: 12

Бренд: Hiltron Страницы: 64

Бренд: Trailer Vision Страницы: 18

Magnavox FW 55C

Бренд: Magnavox Страницы: 80

Бренд: Malone Страницы: 19

Бренд: Absolute Process Instruments Страницы: 2

MAGNUM TIG THF 238 PRO

Бренд: Spaw Страницы: 10

Бренд: Gemini Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды