EWM Phoenix 355 Progress puls MM TKM Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 128

background image

Design and function

Special parameters (advanced settings)

099-005403-EW501

18.08.2016

91

5.10.1 Selecting, changing and saving parameters

ENTER (Enter the menu)
• Switch off machine at the main switch.
• Press and hold the "left parameter selection" button and switch the machine on again at the

same time.

NAVIGATION (Navigate the menu)
• Select parameters by turning the "welding parameter setting" rotary dial.
• Set or change the parameters by turning the "arc length correction/select welding program"

rotary dial.

EXIT (Exit the menu)
• Press the "right parameter selection" button (switch machine off and on again).

ENTER

B

A

A

l

0

l

0

+

EXIT

B

NAVIGATION

A

B

A

Figure 5-73

Display

Setting/selection

Ramp time for wire inching

0 = -------- normal inching (10s ramp time)
1 = -------- fast inching (3s ramp time) (Ex works)

Block program "0"

0 = -------- P0 enabled (Ex works)
1 = -------- P0 blocked

Display mode for Up/Down welding torch with one-digit 7-segment display (two
keys)

0 = -------- normal display (ex works) program number/welding power (0

–9)

1 = -------- display toggles between program number/welding type

Program limitation

Programs 1 to max. 15
Ex works: 15

Special cycle in the special latched and non-latched operating modes

0 = -------- normal (previous) non-latched/latched (Ex works)
1 = -------- WF3 cycle for non-latched/latched

«
...
89
90
91
92
93
...
»

Содержание Phoenix 355 Progress puls MM TKM

































































































































Отзывы:

Нет отзывов

Похожие инструкции для Phoenix 355 Progress puls MM TKM

Бренд: GANTERUD Страницы: 24

Бренд: CAME Страницы: 80

Бренд: EarthQuake Страницы: 6

JBL BAR 5.1 SURROUND

Бренд: Harman Страницы: 4

Бренд: Harman Страницы: 48

Infinity KAPPA 4100msb

Бренд: Harman Страницы: 8

JBL PARTYBOX ON-THE-GO

Бренд: Harman Страницы: 17

Бренд: R. Beck Maschinenbau Страницы: 35

JBL CINEMA SB190

Бренд: Harman Страницы: 19

JBL BAR 5.0 MULTIBEAM

Бренд: Harman Страницы: 25

Бренд: Neets Страницы: 14

Бренд: Hafele Страницы: 57

Бренд: R&M Страницы: 53

Бренд: Ravaglioli Страницы: 90

Бренд: TDSi Страницы: 2

Бренд: VeGue Страницы: 12

Бренд: La Crosse Technology Страницы: 2

Бренд: salmson Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды