EWM Phoenix 355 Progress puls MM TKM Скачать руководство пользователя страница 61

Страница: 61 / 128

Design and function

MIG/MAG welding

099-005403-EW501

18.08.2016

Special latched with changing welding method by tapping (process switching)

For machine versions with pulsed arc welding procedures only.

To activate or set the function

> see 5.3.16 chapter

Figure 5-37

1st cycle

•  Press and hold torch trigger.
•  Shielding gas is expelled (gas pre-flows)
•  Wire feed motor runs at "creep speed"
•  Arc ignites after

the wire electrode makes contact with the workpiece, welding current is flowing (start

program P

START

)

2nd cycle

• Release torch trigger
• Slope on main program P

The slope on main program P

is given at the earliest after the set time t

START

elapses and at the

latest when the torch trigger is released.
Tapping (pressing the torch trigger for less than 0.3 sec.) changes over the welding process (P

If a standard process has been defined in the main program, tapping changes to the pulse
process, and tapping again will return to the standard process, etc.
3

cycle

• Press and hold torch trigger
• Slope to end program P

END

4th cycle

•  Release torch trigger
•  WF motor stops
•  Arc is extinguished after the pre-selected wire burn-back time elapses
•  Gas post-flow time elapses

This function can be activated using the PC300.Net software.
Refer to the software operating instructions.

Содержание Phoenix 355 Progress puls MM TKM

































































































































Результаты поиска

Содержание Phoenix 355 Progress puls MM TKM

Отзывы:

Похожие инструкции для Phoenix 355 Progress puls MM TKM

Бренды по названию

Популярные бренды

EWM Phoenix 355 Progress puls MM TKM, Руководство по эксплуатации

Результаты поиска

Содержание Phoenix 355 Progress puls MM TKM

Отзывы:

Похожие инструкции для Phoenix 355 Progress puls MM TKM

Бренды по названию

Популярные бренды