EWM Phoenix 355 Progress puls MM TKM Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 128

background image

Design and function

Special parameters (advanced settings)

102

099-005403-EW501

18.08.2016

Selecting programs with the standard torch trigger (P17)

Allows you to select a program or switch a program before starting welding.
You switch to the next program by tapping the torch trigger. Once the last enabled program is reached,
you start again at the beginning.
• Program 0 is the first enabled program, provided that it is not blocked.

(see also special parameter P2).

• The last enabled program is P15.

-



If the programs are not limited by special parameter P4 (see special parameter P4).

-



Or if the programs are limited for the selected JOB by the n cycle setting (see parameter P8).

• Welding starts when the torch trigger is held for longer than 0.64 s.

You can select programs with the standard torch trigger in all operating modes (non-latched, special non-
latched. latched and special latched).

Switching the operating mode and welding type using the wire feed control (P18)

Selecting the operating mode (non-latched, latched, etc.) and welding type (MIG/MAG standard
welding/pulse arc welding) at the wire feed unit control or the welding machine control.
• P18 = 0

-



Program 0: To select the operating mode and welding type at the wire feed unit.

-



Program 1-15: To select the operating mode and welding type at the welding machine.

• P18 = 1

-



Program 0-15: To select the operating mode and welding type at the wire feed unit.

Mean value display for superPuls (P19)

Function active (P19 = 1)

• For superPuls, the performance

mean value

from program A (P

A

) and program B (P

B

) is shown on the

display (ex factory).

Function inactive (P19 = 0)

• Only the performance of program A is displayed for superPuls.

If the function is enabled and only "000" is shown on the machine display, this is a rare case of
an incompatible system set-up. Solution: Disable special parameter P19.

Predefined execution of the pulsed arc welding process in the PA program (P20)

For machine versions with pulsed arc welding procedures only.

Function active (P20 = 1)

• If the superPuls and welding process switching functions are available and activated, the pulse arc

welding process is always executed in the main program PA (ex factory).

Function inactive (P20 = 0)

• Predefined execution of the pulse arc welding process in the PA program is disabled.

«
...
100
101
102
103
104
...
»

Содержание Phoenix 355 Progress puls MM TKM

































































































































Отзывы:

Нет отзывов

Похожие инструкции для Phoenix 355 Progress puls MM TKM

Бренд: C&K systems Страницы: 28

Бренд: C&K systems Страницы: 2

Бренд: C&K systems Страницы: 40

Бренд: C-TEC Страницы: 10

Бренд: Geberit Страницы: 49

Бренд: jablotron Страницы: 8

Бренд: Vacron Страницы: 2

SAF-FRO PRESTOTIG 240 AC/DC

Бренд: Air Liquide Страницы: 121

Drive 4 Basic S

Бренд: EWM Страницы: 52

Бренд: Alto Страницы: 40

Бренд: Lincoln Electric Страницы: 12

paddy 000121300000

Бренд: Menabo Страницы: 34

Бренд: EAW Страницы: 2

Бренд: Microlab Страницы: 4

Бренд: gala gar Страницы: 28

Бренд: Dometic Страницы: 24

Invertec V305-T AC

Бренд: Lincoln Electric Страницы: 2

CBS-5000H Series

Бренд: Fetco Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды