EWM Phoenix 355 Progress puls MM TKM Скачать руководство пользователя страница 28

Страница: 28 / 128

Design and function

Transport and installation

099-005403-EW501

18.08.2016

Fully unroll welding current leads, torch hose packages and intermediate hose packages. Avoid
loops!

Always keep leads as short as possible!

Lay any excess cable lengths in meanders.

Figure 5-6

5.1.7.1 Stray welding currents

WARNING

Risk of injury due to stray welding currents!
Stray welding currents can destroy protective earth conductors, damage machines and
electronic devices and cause overheating of components, leading to fire.

• Check that all welding current connections are firmly secured and electrical connections are

in perfect condition.

• Set up, attach or suspend all conductive power source components such as casing,

transport vehicles and crane frames so they are insulated.

• Do not place any other electronic devices such as drills or angle grinders on the power

source, transport vehicle or crane frames unless they are insulated.

• Always put welding torches and electrode holders on an insulated surface when they are

not in use.

Figure 5-7

Содержание Phoenix 355 Progress puls MM TKM

































































































































Результаты поиска

Содержание Phoenix 355 Progress puls MM TKM

Отзывы:

Похожие инструкции для Phoenix 355 Progress puls MM TKM

Бренды по названию

Популярные бренды

EWM Phoenix 355 Progress puls MM TKM, Руководство по эксплуатации

Результаты поиска

Содержание Phoenix 355 Progress puls MM TKM

Отзывы:

Похожие инструкции для Phoenix 355 Progress puls MM TKM

Бренды по названию

Популярные бренды