EWM Phoenix 355 Progress puls MM TKM Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 128

background image

Design and function

Special parameters (advanced settings)

099-005403-EW501

18.08.2016

101

Lower and upper limits of the remote JOB changeover process (P13, P14)

The highest and lowest JOB numbers which can be selected using accessory components, such as the
PowerControl 2 torch.
Avoids an accidental changeover into undesirable or undefined JOBs.

Hold function (P15)
Hold function active (P15 = 1)

• Mean values for the last main program parameters used for welding are displayed.

Hold function not active (P15 = 0)

• Setpoint values for the main program parameters are displayed.

Block JOB mode (P16)
The following accessory components support block JOB mode:

• Up/Down welding torch with one-digit 7-segment display (two keys)

Program 0 is always active in JOB 0 and program 1 in all other JOBs

In this operating mode, a total of 27 JOBs (welding tasks) divided into three blocks can be called up using
accessory components.

The following settings must be made in order to be able to use block JOB mode:

•  Switch the "Program or Up/Down function" changeover switch to "Program"
•  Set the JOB list to actual JOB list (special parameter P12 = "1")
•  Enable block JOB mode (special parameter P16 = "1")
•  Change to block JOB mode by selecting one of the special JOBs 129, 130 or 131.

Simultaneous operation with interfaces such as RINT X12, BUSINT X11, DVINT X11 or digital
accessory components such as is the R40 remote control is not possible!
Allocation of JOB numbers to the display on the accessory components

JOB no.

Display/selection on the accessory component

0

1

2

3

4

5

6

7

8

9

Special JOB 1

129

141

142

143

144

145

146

147

148

149

Special JOB 2

130

151

152

153

154

155

156

157

158

159

Special JOB 3

131

161

162

163

164

165

166

167

168

169

JOB 0:

This JOB allows you to set the welding parameters manually.
Selection of JOB 0 can be prevented via the key switch or with the "block program 0" parameter (P2).
Key switch position 0, or special parameter P2 = 0: JOB 0 is blocked.
Key switch position 1, or special parameter P2 = 1: JOB 0 can be selected.

JOBs 1-9:

Nine JOBs can be called up in each special JOB (see table).
Nominal values for wire speed, arc correction, dynamics etc must be defined in advance in these JOBs.
This can be done easily with the PC300.NETsoftware.
If the software is not available, user-defined JOB lists can be created in the special JOB areas with the
"Copy to" function. (See explanations about this in the "Switching JOB lists (P12)" chapter)

«
...
99
100
101
102
103
...
»

Содержание Phoenix 355 Progress puls MM TKM

































































































































Отзывы:

Нет отзывов

Похожие инструкции для Phoenix 355 Progress puls MM TKM

Бренд: GE Страницы: 36

Бренд: Handicare Страницы: 32

Бренд: Harman Kardon Страницы: 2

Бренд: Harman Kardon Страницы: 2

Бренд: JBL Страницы: 24

Бренд: biodex Страницы: 20

Бренд: Telwin Страницы: 108

Бренд: UDP Technology Страницы: 17

Бренд: iStorage Страницы: 2

Бренд: Patrol Hawk Страницы: 13

Бренд: 4Ddoors Страницы: 20

Бренд: JBL Страницы: 11

Jellyball FT12JB

Бренд: Fenton Страницы: 16

Бренд: deconta Страницы: 12

Бренд: Parweld Страницы: 16

Бренд: Aiwa Страницы: 76

Бренд: WG Страницы: 32

Бренд: AMGO Hydraulics Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды