Evo Affinity 30Ge Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 29

background image

OPERATOR INSTRUCTIONS

A f f i n i t y 3 0 G e

Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA

Phone 503.626.1802 | Fax 503.213.5869 | www.evoamerica.com | [email protected]

25

The Affi nity grill has removable ninth-pan spillover trays concealed in sliding drawers on both the right and left side of
the front control panel. When closed, these trays align with the drip pan Spillover Slots allowing cooking debris to be
wiped from the pan into the slots and to the spillover tray below. It is very important to monitor the level of spillover in
the trays, and immediately empty when they are near full.

Opening Spillover Tray Drawers

- To open a drawer, grasp the drawer at its bottom side and pull forward. When

grasping the drawer you will notice a Drawer Pull Recess which causes a reveal at the underside of the drawer. Place
your hand under the drawer front and pull forward to extend the drawer until it stops.

Removable Drawer Slides

- The drawers are easily removed by fi rst extending the drawer, and then simultaneously

depressing the recessed catches on both the inner and outer slide rails. Once removed, the drawer interior may be
cleaned. Installation is the reverse of removal, taking care to install the rails into each corresponding rail guide.

Do not operate cook top or clean drip pan into spillover slots without spillover trays installed
in spillover drawers. Failure to install ninth-pan spillover trays will result in cooking grease
contamination to the underside of drawer. This requires immediate drawer removal and cleaning.

Do not allow spillover liquids or debris down spillover slots when drawers are open. Any liquids
or debris that may fall into this area when drawers are open should be immediately wiped with a
dry cloth, and keep this area clean at all times.

Do not allow the spillover trays to overfl ow, and do not allow full trays to splash over edge when
opening drawers. Spillover debris and liquids can be hot and cause burns, and/or damage to the
internal operation of the grill.

REMOVABLE SPILLOVER TRAYS

Removable

Drawer Slides

Removable Ninth-Pan

Spillover Tray

Drawer Pull

Recess

Spillover Slot

«
...
23
24
25
26
27
...
»

Содержание Affinity 30Ge






























Отзывы:

Нет отзывов

Похожие инструкции для Affinity 30Ge

Бренд: GASLAND chef Страницы: 48

Бренд: Jenn-Air Страницы: 36

Бренд: Thermador Страницы: 44

Бренд: Thermador Страницы: 62

Бренд: Frigidaire Страницы: 16

Бренд: Frigidaire Страницы: 12

Бренд: Frigidaire Страницы: 12

Бренд: Frigidaire Страницы: 17

318201426 (0810)

Бренд: Frigidaire Страницы: 20

Бренд: Frigidaire Страницы: 24

Бренд: Frigidaire Страницы: 12

Бренд: Frigidaire Страницы: 16

Бренд: Frigidaire Страницы: 12

Бренд: Frigidaire Страницы: 16

318200682 (0604) Rev

Бренд: Frigidaire Страницы: 12

318205454 (1302)

Бренд: Frigidaire Страницы: 12

Бренд: Frigidaire Страницы: 12

Бренд: Frigidaire Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды