Evo Affinity 30Ge Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 29

background image

INSTALLATION INSTRUCTIONS

A f f i n i t y 3 0 G e

Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA

Phone 503.626.1802 | Fax 503.213.5869 | www.evoamerica.com | [email protected]

3

WARNING

This symbol identifi es the most important
safety messaging in this manual. When you
see this symbol, be alert to the possibility of
serious bodily injury if the instructions are
not followed. Be sure to read and carefully
follow all of the messages.

Grill is for indoor use only. Grill should be operated in a well-ventilated space. Never operate
near fl ammable liquids or vapors. Do not install or use grill within 36” of combustible materials
from back and sides of grill. Grill shall not be located under unprotected overhead made of
combustible construction.

WARNING

Warnings

FOR YOUR SAFETY

If You Smell Gas:
1. Shut off gas to appliance.
2. Extinguish any open fl ame.
3. Remove grill cooking surface.
4. If odor continues, immediately call your

gas supplier or your fi re department.

5. Evacuate all personnel from the area.

FOR YOUR SAFETY

1. Do not store or use gasoline or other

fl ammable vapors and liquids in the
vicinity of this or any other appliance.

2. An LP Tank not connected for use shall

not be stored in the vicinity of this or
any other appliance.

It is the responsibility of the assembler/owner
to assemble, install and maintain gas grill.
Do not let children operate or play near your
grill. Failure to follow these instructions could
result in serious personal injury and / or
property damage.

WARNING

Improper installation, adjustment, alteration, service or maintenance can cause property dam-
age, injury or death. Read the installation, operating and maintenance instructions thoroughly
before installing or servicing this equipment.

WARNING

«
1
2
3
4
5
...
»

Содержание Affinity 30Ge






























Отзывы:

Нет отзывов

Похожие инструкции для Affinity 30Ge

Digital Radiant Cooktop

Бренд: GE Страницы: 24

Бренд: Taurus Страницы: 48

Бренд: Inalto Страницы: 17

36" (91.4 CM) ELECTRIC DOWNDRAFT COOKTOP

Бренд: Jenn-Air Страницы: 24

U22062 CSIG 509

Бренд: Parkinson Cowan Страницы: 24

Бренд: M-system Страницы: 48

Бренд: Freggia Страницы: 64

Бренд: Kuppersbusch Страницы: 12

Бренд: Hotpoint Страницы: 44

Бренд: Parkinson Cowan Страницы: 41

Бренд: M-system Страницы: 160

Бренд: Jenn-Air Страницы: 3

Бренд: Bellini Страницы: 33

Бренд: Belling Страницы: 60

Kensington 1100 DF

Бренд: Belling Страницы: 82

Бренд: Belling Страницы: 130

Essentials CFSE60W17

Бренд: Currys Страницы: 24

Бренд: Faber Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды