Evo Affinity 30Ge Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 29

background image

INSTALLATION INSTRUCTIONS

A f f i n i t y 3 0 G e

Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA

Phone 503.626.1802 | Fax 503.213.5869 | www.evoamerica.com | [email protected]

8

Cook Surface

: Lift and separate cook surface from unit and place next to installation area.

Drip Pan Gasket:

Gasket is secured

to top of drip tray.

Remove gasket

from drip tray

and set aside

for reinstallation.

Drip Pan

Unlatch pan
from circular
skirt, then
carefully lift and
separate drip
pan from unit
and place next
to installation
area.

Take care

not to scratch
drip pan during
installation.

Chassis:

Lift chassis

from crating box

and place on

its side next to

installation area.

Use caution

since ignition

components

are exposed.

Metal Right Angle Brackets:

Unscrew from unit

and keep screws and brackets handy for fi rst
installation step.

3-wire service line:

Black, white

and green

UNPACKING COOKTOP COMPONENTS

STEP 1:

As you are unpacking the crate, make sure you locate all components before

installation.

Ignition components are exposed during uncrating and installation.
Use caution and do not alter factory set positions.

Use caution when lifting. The cook surface is heavy.

«
...
6
7
8
9
10
...
»

Содержание Affinity 30Ge






























Отзывы:

Нет отзывов

Похожие инструкции для Affinity 30Ge

Бренд: Hotpoint Страницы: 32

Бренд: Harbor Freight Tools Страницы: 5

MagnaWave MC1500

Бренд: CookTek Страницы: 11

Бренд: Viking Страницы: 2

Бренд: Omega Страницы: 22

Бренд: Bosch Страницы: 76

Бренд: GE Страницы: 16

Бренд: GE Страницы: 2

JP346BMBB - 30" Smoothtop Electric Cooktop

Бренд: GE Страницы: 2

Бренд: GE Страницы: 16

Бренд: GE Страницы: 40

Бренд: GE Страницы: 20

Бренд: GE Страницы: 16

Бренд: GE Страницы: 16

Бренд: GE Страницы: 2

Бренд: GE Страницы: 16

Бренд: GE Страницы: 2

Бренд: GE Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды