Eurotherm 216 Скачать руководство пользователя страница 30

Страница: 30 / 40

OLH

Out maximum limit (in % of the out).
Span:
- From 0 to 100 when the instrument is

configured with one control out.

- From -100 to 100 when the instrument

is configured for two control outs.

tOL

Duration of the out power limiter (in
minutes).
Available only if Pb is not 0.
Span: from 1 to 540 min. Above this limit,
the display shows "

Inf

" and the

limitation is always entered.
NOTE

NOTE

NOTE: Parameter tOL can be modified
but the new value will only become
operative at the next instrument start up
unless the new value is

Inf

6 .

6 . ERROR MESSAGES

ERROR MESSAGES

6.1

6.1 MEASUREMENT ANOMALY SIGNAL

MEASUREMENT ANOMALY SIGNAL

The instrument display (the upper display for
model 0316) shows the OVERRANGE and
UNDERRANGE conditions with the following
indications:

Overrange

Underrange

The example shows the display of model 0316.
Model 0216 displays 4 digits.

The sensor break can be signalled as:
- for TC/mV input

: OVERRANGE or

UNDERRANGE selected
by a solder jumper

- for RTD input

: OVERRANGE

On RTD input, a special test is provided to signal
OVERRANGE when input resistance is less than
12 ohm (Short circuit sensor detection).

NOTE

NOTE:
When:
- The instrument is set for one control out only

and an OVERRANGE is detected, the OUT 1
turns OFF (if reverse action) or ON (if direct
action).

- The instrument is set to use two control outs

and an OVERRANGE is detected, OUT 1 turns
OFF and OUT 2 turns ON.

- The instrument is set for one control out only

and an UNDERRANGE is detected, the OUT 1
turns ON (if reverse action) or OFF (if direct
action).

02-0316-1-DER.pmd

22/04/2004, 16.19

Содержание 216









































Результаты поиска

Содержание 216

Отзывы:

Похожие инструкции для 216

Бренды по названию

Популярные бренды

Eurotherm 216, Руководство пользователя

Результаты поиска

Содержание 216

Отзывы:

Похожие инструкции для 216

Бренды по названию

Популярные бренды