e
n
Do not use pressurised water to wash the
machine and/or interchangeable equip-
ment. Doing so can damage the motor
and any electrical systems or batteries.
Avoid excessive use of water near labels.
In the event of damage, labels must be
replaced before using the machine and/
or the interchangeable equipment again.
CAUTION!
CAUTION!
10.6 TYRE INFLATION
If the wheels are not full,
we recommend
checking tyre inflation before each ma-
chine use. The recommended value is 21
PSI (1.5 bar).
Before inflating the tyre, always check
the maximum PSI value on the tyre.
11. CLEANING AND WASHING
Before proceeding, read and understand
the chapter “SAFETY INSTRUCTIONS”
in its entirety.
Wait for all the hot parts to cool down (at
least 20 minutes) before washing and/or
cleaning the machine or the interchange-
able equipment. Use compressed air or a
sponge with neutral detergent and water.
CAUTION!
DANGER!
13. TROUBLESHOOTING
Possible cause
See chapt.
The motor does not
start
No fuel; top up.
7.2
Check that the throttle is set to START/1.
7.3
Check that the spark plug cap is properly inserted.
Specific motor
manual
Check the conditions of the spark plug and clean or replace if necessary.
Specific motor
manual
Check that the fuel cock is open (only for motor models for which the cock is
provided).
Specific motor
manual
Motor power
decreases
Air filter dirty, clean it.
Specific motor
manual
Check if any stone or soil/vegetation residue is stopping the tool rotation, in case
remove them.
The rotavators will
not turn
Adjust the transmission cable registers.
10.4
Check that the rotavators are fixed to the shaft.
-
Check the positioning and conditions of the transmission belts; reposition and/or
replace them.
-
Wheels are not
turning
Check the transmission cables.
10.4
Contact the nearest authorised service centre if the problem cannot be solved.
12. MAINTENANCE PLAN
How often
See chapt.
Checking the tightness of
fasteners and guards
Always before starting the machine - check that there are no untightened
screws, bolts and/or nuts and that the bonnets and protection systems are
intact and correctly fitted.
-
Cleaning
After each use
11.
Inflation
As needed
10.6
Cable adjustment
If operation is not as according to the manual
10.4
Base oil change
60 hours
10.5
Motor
See specific manual
Содержание MZP 11
