Estate Swing E-S 500 Скачать руководство пользователя

Страница: 55 / 55

E-S 500 / 502 Classic Series Instruction Manual

5.10

Accessories Wiring

Photo Eye, Safety Edge, Safety Loop:

Normally Closed (NC) of safety device

= Photo terminal of PHOTO block on gate opener control

board.

Common (COM) or Ground (GND) of safety device

= GND terminal of PHOTO block on gate

opener control board.

12V Power positive (+) or (12V) or (PWR) of safety device

= V+ terminal of PHOTO block on gate

opener control board.

12V Power Negative (-) or (GND) or (PWR) of safety device

= GND terminal of PHOTO block on

gate opener control board.

*Remove safety jumper from PHOTO terminal if using a safety device.

*12V is not a misprint, the V+ terminal has a 12V output.

Solenoid Gate Lock:

Positive Lead of lock

= A terminal of E_LOCK block on gate opener control board.

Negative Lead of lock

= B terminal of E_LOCK block on gate opener control board.

Magnetic Gate Lock:

Magnetic gate locks must have their own power supply and their own

relay.

Coil of relay for magnetic lock

= A terminal of E_LOCK block on gate opener control board.

Coil of relay for magnetic lock

= B terminal of E_LOCK block on gate opener control board.

Connect positive lead of the power supply directly to the positive lead of the mag lock.
Connect negative lead of the power supply to the N/C terminal of the relay.
Connect the COM terminal of the relay to the negative lead of the mag lock.

Содержание E-S 500
























































Результаты поиска

Содержание E-S 500

Отзывы:

Похожие инструкции для E-S 500

Бренды по названию

Популярные бренды

Estate Swing E-S 500, Инструкция по эксплуатации

Результаты поиска

Содержание E-S 500

Отзывы:

Похожие инструкции для E-S 500

Бренды по названию

Популярные бренды