Estate Swing E-S 500 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 55

background image

E-S 500 / 502 Classic Series Instruction Manual

Standard System Overview and Safety Zone

1.3

The system displayed below is a recommended standard system. Other approved accessories
can be installed. Photo sensors and a flashing light indicating gate movement is recommend-
ed for safety purposes.

1,2

Estate Swing Operator •

3

Photocells (not included) •

4

Control board •

5

N/A

6

Push but-

ton opening device (not included) •

7

Receiver extension (not included) •

8

24Vdc flashing

lamp (not included) •

9

Positive stop (not included) •

10

AC transformer

Notes:

1) When laying electrical cables, use appropriate rigid and/or flexible tube

2) Do not run any wires in the same conduit as 110 AC power that may be in

the area. This will cause danger of electrocution.

IMPORTANT: Preliminary Checks

To ensure safety and an efficiently operating automated system, make sure the follow-
ing conditions are observed.

• The gate and post must be suitable for being automated. Check that the structure is
sufficiently strong and rigid, and its dimensions and weights conform to those Indicated
on page 1.
• Make sure the gates move smoothly without any irregular friction during entire travel.
• Make sure the hinges are in good condition. Ball bearing hinges are necessary for
gates weighing over 200 lbs. or over 10’ in length.
• Make sure the gate is plumb and level.
• The gate post must be secured in the ground with concrete. This will prevent alteration
of alignments and leveling during installation and during cycles.

«
...
6
7
8
9
10
...
»

Содержание E-S 500
























































Отзывы:

Нет отзывов

Похожие инструкции для E-S 500

Бренд: B&D Страницы: 24

Бренд: fadini Страницы: 12

Бренд: fadini Страницы: 12

Бренд: fadini Страницы: 12

Бренд: fadini Страницы: 16

CALYPSO 400 CA43

Бренд: Erreka Страницы: 46

Бренд: LockMaster Страницы: 18

Бренд: Langjushan-Tech Страницы: 12

Power Drive Security+ HD200CD

Бренд: Chamberlain Страницы: 80

Бренд: Nice Страницы: 47

Бренд: CAME Страницы: 22

Бренд: CAME Страницы: 17

Бренд: Chamberlain Страницы: 84

Бренд: FAAC Страницы: 24

Бренд: Hamilton Beach Страницы: 10

Бренд: Salton elite Страницы: 8

GI.BI.DI. DSK40

Бренд: Bandini Industrie Страницы: 14

Glidermatic GRD

Бренд: Gliderol Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды