Estate Swing E-S 500 Скачать руководство пользователя | Manualshive

Страница: 51 / 55

background image

E-S 500 / 502 Classic Series Instruction Manual

5.6

Control Board Overview

CAUTION!

Do not run 110V AC power direct to the board. This

will cause permanent damage to both boards and void your
warranty. Caution!

Gate Opener reactions to signals:

PUSH2 (PUSH 2 terminal and PUSH 2 button):

Details:

• Will activate gate with momentary contact (momentary contact between PUSH2
and V+).
• Controls

both

leaves in 2 leaf mode (Dip switch 2 in the ON position)

•

Only opens the gate, never closes it.

• Pause time is able to be re-set if this terminal is closed through a momentary con-
tact. Then the time will be reset, count down the pause time, and reclose.
•

Ideal for exit wand or exit loop.

Operational Sequence for terminal with auto-close ON (Dip switch 1 in on position):

1. In closed position - momentary contact will open gates.
2. When opening - momentary contact will have no effect.
3. When stopped mid cycle from PUSH 1 or the Receiver - momentary contact will
open the gate.
4. When open with auto-reclose on - momentary contact will re-set pause time and
will start counting again after release of momentary contact.
5. When pause time countdown is stopped in open from a momentary contact of
PUSH 1 or the Receiver - momentary contact will have no effect.
6. When closing - momentary contact will re-open the gate.

Operational Sequence for terminal with auto-close OFF (Dip switch 1 in off position):

1. In closed position - momentary contact will open gates.
2. When opening - momentary contact will have no effect.
3. When stopped mid cycle - momentary contact will open the gate.
4. When open with auto-reclose off - momentary contact will have no effect.
5. When closing - momentary contact will re-open the gate.

PUSH 1 and PUSH 2

– these terminals can hold as many normally open connections as

needed, they will be wired in parallel. They are used for keypads, push buttons, uni-
versal receivers, etc.

«
...
49
50
51
52
53
...
»

Содержание E-S 500
























































Отзывы:

Нет отзывов

Похожие инструкции для E-S 500

Бренд: FAAC Страницы: 29

Бренд: SEA USA Страницы: 16

Бренд: tau Страницы: 36

CanPRO 56050-()

Бренд: Nemco Страницы: 5

Бренд: Key Automation Страницы: 28

Бренд: CAME Страницы: 24

VER-PLUS Series

Бренд: CAME Страницы: 36

Бренд: tau Страницы: 40

Бренд: V2 Страницы: 74

Бренд: Rival Страницы: 4

Бренд: Chamberlain Страницы: 40

Бренд: Chamberlain Страницы: 28

Бренд: DPLUS Страницы: 8

Бренд: DPLUS Страницы: 12

Бренд: Sky Way Страницы: 10

Бренд: GATEXPERT Страницы: 27

Бренд: Raynor Страницы: 36

Бренд: Craftsman Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды