Estate Swing E-S 500 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 55

Estate Swing E-S 500 Скачать руководство пользователя страница 15

E-S 500 / 502 Classic Series Instruction Manual

Installation of Operator —Pull-to-Open

2.4

1)  Locate  the  set  back  template  found  in  the
box  to  determine  the  proper  setback.  Create
a template out of the boomerang bracket by
tracing it on a piece of cardboard.

2)  Find  the  proper  setback  for  your  operator
(from  previous  page).  Hold  the  lower  “L”
shaped  bracket  along  with  the  boomerang
bracket  template  against  the  post  near  the
hinge. [

See Fig. 1

]

Mark how much of the boomerang bracket
you will trim off on the template.

The hole on

the end of the boomerang bracket should be
in the setback position.

NOTE:

The “L” shape brackets in our illustrations

are on the opposite side of the post as the
hinges. The “L” shape brackets in your situation
may be on the rear face of the post, this will be
determined by the relation of the setback to
the hinge location of your gate.

3) Trim boomerang bracket template, then
double check setback positioning.
Using the template, mark the boomerang
bracket for cutting. [

See Fig. 2

]

4) Cut off the excess length (if any) of the
boomerang bracket using a sawzall or hack-
saw.

Fig 1

Fig 2

Alternate Mounting Option

«
...
13
14
15
16
17
...
»

Содержание E-S 500
























































Отзывы:

Нет отзывов