Ericsson CME 20 R6.0 Скачать руководство пользователя страница 61

Страница: 61 / 307

Product Specification for RBS 2302

5.4.2

Variants

Radio Configurations

The RBS will support the following basic configuration alternatives:

Table 7

GSM 900

GSM 1800

GSM 1900

M9d_2.2

M18d_2.2

M19d_2.2

The performance for each configuration is described in chapter Radio
Configurations, RBS 2000 Micro.

02_0345A

CDU type

Frequency band

Duplexer

Number of antenna ports

Number of transcievers

d _ 2 . 2

Figure 27

How to read the code

Table 8

Object

RBS Variants

Traffic capacity

2 TRX

Encryption

A5/1, A5/2

Transport Network Interface

1.5 Mbit/s, 100 Ohm

2.0 Mbit/s, 75 Ohm

2.0 Mbit/s, 120 Ohm

Filter

Duplex

It is possible to equip the RBS with either external antennas, integral
antennas or an active antenna system (MAXITE

Using the active antenna, the RBS supports a “highway configuration”,
where two TRXs cover two directions as one cell, as specified below.

It is also possible to extend one cabinet with up to two other cabinets to
form a 4 or 6 TRX site.

The RBS supports a multicasting box, as specified below.

The RBS 2302 will support the following basic configuration
alternatives:

60 (306)

EN/LZT 123 2697

R5A

1998-08-13

Содержание CME 20 R6.0
























































































































































































































































































Результаты поиска

Содержание CME 20 R6.0

Отзывы:

Бренды по названию

Популярные бренды

Ericsson CME 20 R6.0, Справочное руководство

Результаты поиска

Содержание CME 20 R6.0

Отзывы:

Бренды по названию

Популярные бренды