Ericsson CME 20 R6.0 Скачать руководство пользователя страница 133

Страница: 133 / 307

Radio Reception

P003071A

X=TX ref. point

RBS Border

Cabinet

Combining

system

Filtering

Figure 33

RX reference point x

When the RBS is configured with integral antenna the RX reference
point is the cabinet input RF connector.

The antenna gain is defined as the total received gain, including the
radome attenuation between the air interface and the RX reference point.

P003070A

X=TX ref. point

RBS Border

Cabinet

Combining

system

Filtering

Figure 34

RX reference point with integral antenna

19.3

Functions

19.3.1

Radio Reception

Radio reception denotes the function to "Receive an RF signal" and
restore the bit stream that constitutes a burst.

The GSM specification of Receiver characteristics is found in /
GSM:05.04/ and /GSM:05.05/.

The PCS specification of Receiver characteristics is found in /PCS:4/, /
PCS:5/ and /PCS:6/.

19.4

Operational Conditions

19.4.1

Frequency Band

The receiver can operate in the extended GSM 900 frequency band, 880
- 915 MHz. The Combining system supports the primary GSM band,
890 - 915 MHz, see /GSM:05.05:2/.

132 (306)

EN/LZT 123 2697

R5A

1998-08-13

Содержание CME 20 R6.0
























































































































































































































































































Результаты поиска

Содержание CME 20 R6.0

Отзывы:

Бренды по названию

Популярные бренды

Ericsson CME 20 R6.0, Справочное руководство

Результаты поиска

Содержание CME 20 R6.0

Отзывы:

Бренды по названию

Популярные бренды