Ericsson CME 20 R6.0 Скачать руководство пользователя страница 23

Страница: 23 / 307

Radio Configurations, RBS 2000 Micro

Transport network

Antenna
system

BTS Base Transceiver Subsystem

Site

Cell

BTS

01_0388A

RBS 2000

Figure 10

An RBS 2000 site with three cells

3.2.2

Antenna System

Is constituted by all RF transmission and reception antennas, directed to
cover the same area or multicasting configuration.

Antenna Reference Point (ARP)

Two ARP are defined in this document; the RBS ARP and
the AAU V

(1)

-ARP.

The RBS ARP is the feeder connector on the RBS.

The AAU V-ARP is the test connector after the network that connects
the outputs from different PAM:s. This network is used for test
purposes only.

(1)

V=Virtual

3.2.3

Basic Configuration

A maximum of two transceivers can be combined and connected to one
antenna system.

The basic configuration may be multiplied or used in combination with
other basic configurations to build the needed site equipment.

3.2.4

Definition

The definition of the basic configuration type thus refers to CDU_type.

<Basic_Config>::=<X><F>d_<A>.<T>\<N>

22 (306)

EN/LZT 123 2697

R5A

1998-08-13

Содержание CME 20 R6.0
























































































































































































































































































Результаты поиска

Содержание CME 20 R6.0

Отзывы:

Бренды по названию

Популярные бренды

Ericsson CME 20 R6.0, Справочное руководство

Результаты поиска

Содержание CME 20 R6.0

Отзывы:

Бренды по названию

Популярные бренды