manualshive.com logo in svg

Epson S1C63003, Техническое руководство

Технический мануал для Epson S1C63003 - это важный ресурс для обладателей данного устройства. Скачайте бесплатно мануал по ссылке manualshive.com, чтобы узнать всю необходимую информацию о его работе и функциональных возможностях. Понятные инструкции помогут вам эффективно использовать продукт.

Поделиться
Скачать
background image

aPPenDiX e  SuMMaRY OF nOTeS

aP-e-2

 

Seiko epson Corporation 

S1C63003/004/008/016 TeChniCal Manual

 

 

(Rev. 1.1)

Oscillation circuit

•  When high speed CPU operations are not necessary, you should operate the peripheral circuits with the setting 

shown below. 

  - CPU operating clock: 

OSC1

  - OSC3 oscillation circuit: Off (When the OSC3 clock is not necessary for peripheral circuits.)
  - Clock manager: 

Disable the clock supply to unnecessary peripheral circuits.

•  Since several tens of µsec to several tens of msec are necessary for the oscillation to stabilize after turning the 

OSC3 oscillation circuit on. Consequently, you should switch the CPU operating clock (OSC1 

→

 OSC3) after 

allowing for a sufficient waiting time once the OSC3 oscillation goes on. The oscillation start time will vary 
somewhat depending on the resonator and externally attached parts. Refer to the oscillation start time example 
indicated in the "Electrical Characteristics" chapter.

•  When switching the clock from OSC3 to OSC1, be sure to switch OSC3 oscillation off with separate instruc-

tions. Using a single instruction to process simultaneously can cause a malfunction of the CPU.

•  Both the OSC1 and OSC3 oscillation circuits stop oscillating when the CPU enters SLEEP mode. To prevent 

the CPU from a malfunction when it resumes operating from SLEEP mode, switch the CPU clock to OSC1 
before placing the CPU into SLEEP mode.

Watchdog timer

•  When the watchdog timer is being used, the software must reset it within 3-second cycles.

•  Because the watchdog timer is set in operation state by initial reset, set the watchdog timer to disabled state 

(not used) before generating an interrupt (NMI) if it is not used.

Clock timer

•  Be sure to read timer data in the order of low-order data (TM[3:0]) then high-order data (TM[7:4]).

•  The clock timer count clock does not synch with the CPU clock. Therefore, the correct value may not be ob-

tained depending on the count data read and count-up timings. To avoid this problem, the clock timer count 
data should be read by one of the procedures shown below.
- Read the count data twice and verify if there is any difference between them.
- Temporarily stop the clock timer when the counter data is read to obtain proper data.

•  When resetting the clock timer (TMRST = "1"), do not start the clock timer (TMRUN = "1") simultaneously. 

If both control bits are set to "1," the clock timer may not reset properly.

Stopwatch timer

•  The interrupt factor flag should be reset after resetting the stopwatch timer.

•  Be sure to data reading in the order of SWD[3:0] 

→

 SWD[7:4] 

→

 SWD[11:8].

•  When data that is held by a LAP input is read, read the capture buffer renewal flag CRNWF after reading the 

SWD[11:8] and check whether the data has been renewed or not. (S1C63004/008/016)

•  When  performing  a  processing  such  as  a  LAP  input  preceding  with  1  Hz  interrupt  processing,  read  the 

LAP  data  carry-up  request  flag  LCURF  before  processing  and  check  whether  carry-up  is  needed  or  not. 

(S1C63004/008/016)

Programmable timer

•  When  reading  counter  data,  be  sure  to  read  the  low-order  4  bits  (PTDx[3:0])  first. The  high-order  4  bits 

(PTDx[7:4]) are latched when the low-order 4 bits are read and they are held until the next reading of the low-
order 4 bits. In 16-bit timer mode, the high-order 12 bits are held by reading the low-order 4 bits, be sure to 

read the low-order 4 bits first. When the CPU is running with the OSC1 clock and the programmable timer is 
running with the OSC3 clock, stop the timer before reading the counter data to read the proper data. 

•  The programmable timer actually enters RUN/STOP status in synchronization with the falling edge of the input 

clock after writing to the PTRUNx register. Consequently, when "0" is written to the PTRUNx register, the 
timer enters STOP status at the point where the counter is decremented (-1). The PTRUNx register maintains 
"1" for reading until the timer actually stops.

Содержание S1C63003
































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S1C63003

KAESER KOMPRESSOREN SIGMA CONTROL 2 User Manual preview
SIGMA CONTROL 2
Бренд: KAESER KOMPRESSOREN Страницы: 246
XtendLan KEYBPTZ4D Operating Instructions Manual preview
KEYBPTZ4D
Бренд: XtendLan Страницы: 12
Nuvoton NuMicro M252 Series User Manual preview
NuMicro M252 Series
Бренд: Nuvoton Страницы: 38
Cypress Semiconductor CY8CKIT-015 Manual preview
CY8CKIT-015
Бренд: Cypress Semiconductor Страницы: 36
Vega VEGATOR 131 Operating Instructions Manual preview
VEGATOR 131
Бренд: Vega Страницы: 28
WATSON W91 Series Installation, Operation & Maintenance Instructions Manual preview
W91 Series
Бренд: WATSON Страницы: 16
Danfoss AME 56 Instructions Manual preview
AME 56
Бренд: Danfoss Страницы: 16
Curtis 1232E Manual preview
1232E
Бренд: Curtis Страницы: 30
Sulion Driver VISIO IoT Manual preview
Driver VISIO IoT
Бренд: Sulion Страницы: 8
Sentiotec K2-NEXT Installation And Operating Instructions Manual preview
K2-NEXT
Бренд: Sentiotec Страницы: 92
Pellet Grill Outlet 180-LV Installation Instructions And User Manual preview
180-LV
Бренд: Pellet Grill Outlet Страницы: 4
Frigicoll Kaysun KC-03.2 SPS Installation And Owner'S Manual preview
Kaysun KC-03.2 SPS
Бренд: Frigicoll Страницы: 44
GAC EEG7000 Manual preview
EEG7000
Бренд: GAC Страницы: 22
National Instruments GPIB PCI-GPIB Getting Started preview
GPIB PCI-GPIB
Бренд: National Instruments Страницы: 31
Delta Regis BECT832-SSO Operation Manual preview
BECT832-SSO
Бренд: Delta Regis Страницы: 15
Texas Instruments Chipcon Products CC1110DK Quick Start Instructions preview
Chipcon Products CC1110DK
Бренд: Texas Instruments Страницы: 3
Parker PAC120 Series Operation Manual preview
PAC120 Series
Бренд: Parker Страницы: 31
Jabra LINK 28 User Manual preview
LINK 28
Бренд: Jabra Страницы: 13

Бренды по названию

Популярные бренды

Загрузить еще бренды