Endress+Hauser Silometer FMC 672 Z Скачать руководство пользователя страница 14

Страница: 14 / 64

Monorack housing

The Silometer FMC 672 Z/677 Z transmitter and Monorack housing are supplied
separately. The system must be assembled as shown in Fig. 2.3 before use.

•

The Monorack is prepared for wall- or rail-mounting, degree of protection
IP 40 or IP 30 respectively.

•

The site must be chosen such that the operating temperature of
-20°C

…

+60°C for one Monorack and -20°C

…

+50°C for Monorack banks is

not exceeded.

Full details of the Monorack installation procedure can be taken from the manual supplied
with it.

Monorack protective
housing

If the Silometer FMC 672 Z/677 Z transmitter and Monorack housing are to be mounted
at an exposed site, then it is recommended that they be installed in the protective
housing, degree of protection IP 55, which is available as an accessory.

•

The protective housing accomodates two Silometer FMC 672 Z/677 Z
transmitters.

•

The permissible ambient temperature is -20°C

…

+50°C for one Monorack and

-20°C

…

+40°C for two.

Dimensions and instructions for installation are to be found in the Technical Information
sheet TI 099/00/e.

BA064E10

Plug-in card

Monorack
housing

Monorack base
(terminal block)

Retaining
screws

Retaining
flap

Fig. 2.3:

Assembly and disassembly of

the Monorack housing

Power
pack

Fig. 2.4:

Monorack protective housing

Silometer FMC 672 Z/677 Z

Chapter 2: Installation

Содержание Silometer FMC 672 Z

































































Результаты поиска

Содержание Silometer FMC 672 Z

Отзывы:

Похожие инструкции для Silometer FMC 672 Z

Бренды по названию

Популярные бренды

Endress+Hauser Silometer FMC 672 Z, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Silometer FMC 672 Z

Отзывы:

Похожие инструкции для Silometer FMC 672 Z

Бренды по названию

Популярные бренды