Emerson Fisher FLOBOSS 407 Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 200

background image

FloBoss 407 Instruction Manual

Rev 5/00

3-45

Common Specifications

INPUT

VIBRATION

MECHANICAL
SHOCK

Loop Resistance (Rl)

: 4.5

kilohms maximum.

Frequency Response:

0 to 10 Hz

maximum, 50% duty cycle.

Input Filter (Debounce):

Software filter is configured as the
amount of time that the input must
remain in the active state to be
recognized.

20 Gs peak or 0.06 in. double
amplitude, 10 to 2,000 Hz, per
MIL-STD-202 method 204
condition F.

1500 Gs 0.5 mS half sine per MIL-
STD-202 method 213, condition F.

WEIGHT

CASE

ENVIRON-
MENTAL

APPROVALS

1.3 ounces (37 grams).

Solvent-resistant thermoplastic
polyester, meets UL94V-0. Dimen-
sions are 0.60 in. D by 1.27 in. H by
1.69 in. W (15 mm by 32 mm by 43
mm), not including pins.

Meets the Environmental specifi-
cations of the ROC or FloBoss in
which the module is installed,
including Temperature and Transient
Protection specifications.

Approved by CSA for hazardous
locations Class I, Division 2, Groups
A, B, C, and D.

3.7.5 Discrete Output Modules—Source and Isolated

Source Module Specifications

FIELD WIRING
TERMINALS

OUTPUT

A:

Not used

B:

Positive (to field device)

C:

Negative

Type:

Solid-state relay, current

sourced, normally-open.

Active Voltage:

11 to 30 Vdc

provided.

Active Current:

Limited to 57 mA.

Inactive Current:

Less than 100

microamperes with 30 Vdc source.

Frequency:

0 to 10 Hz maximum.

POWER
REQUIRE-
MENTS

OUTPUT
ISOLATION

SURGE
WITHSTAND

Output Source:

11 to 30 Vdc,

57 mA maximum from ROC
power supply or I/O converter
card.

Module:

4.9 to 5.1 Vdc. 1 mA

in “Off” state; 6 mA in “On” state.

Not isolated. Terminal C tied to
power supply common.

Meets IEEE 472 / ANSI
C37.90a.

«
...
99
100
101
102
103
...
»

Содержание Fisher FLOBOSS 407









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Fisher FLOBOSS 407

Бренд: GARDTEC Страницы: 48

Бренд: FAAC Страницы: 64

Бренд: Panasonic Страницы: 15

Бренд: Panasonic Страницы: 42

Бренд: EasyIO Страницы: 18

Grafica DNE-K07

Бренд: Paradox Страницы: 24

Бренд: Panosol Страницы: 105

Бренд: Pangolin Страницы: 8

Бренд: RadioMaster Страницы: 10

Бренд: Xblue Networks Страницы: 2

Бренд: cinetto Страницы: 56

Бренд: Burlington Страницы: 7

Бренд: TWR Lighting Страницы: 49

Бренд: ECKELMANN Страницы: 147

Бренд: M-system Страницы: 7

Бренд: Festo Страницы: 62

Q.PEAK DUO XL-G11S.X / BFG Series

Бренд: Qcells Страницы: 26

Бренд: EpiSensor Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды