Emerson Fisher FLOBOSS 407 Скачать руководство пользователя страница 55

Страница: 55 / 200

FloBoss 407 Instruction Manual

Rev 5/00

2-33

FloBoss 407 Specifications

PROCESSOR

NEC V25+ running at 10 MHz.

MEMORY

Program:

512 Kbyte flash ROM (electrically

programmable) for firmware, configuration, etc.

Data:

512 Kbyte battery-backed SRAM.

Memory Reset:

When used during power-up, Reset

switch enables a cold start from factory defaults.

TIME FUNCTIONS

Clock Type:

32 kHz crystal oscillator with regulated

supply, battery-backed. Year/Month/Day and
Hour/Minute/Second.

Clock Accuracy:

0.01%.

Watchdog Timer:

Hardware monitor expires after

1.2 seconds and resets the processor. Processor
restart is automatic.

DIAGNOSTICS

These values are monitored and alarmed: RAM
validity/operation, analog input mid-scale voltage,
power input voltage, and board temperature.

COMMUNICATIONS PORTS

Operator Interface:

EIA-232 (RS-232D) format.

Software configured; 300 to 9600 BPS baud rate
selectable. Screw-cap protected connector.

COM1:

EIA-232 (RS-232D) format for general use.

Software configured; 300 to 9600 BPS baud rate
selectable. Eight-terminal connector provided on I/O
board.

COM2:

Serial or modem interface, with optional

communications card. Nine-terminal connector
provided on I/O board.

POWER

Input:

11 to 30 Vdc. 0.8 W typical, excluding power

for input sourcing, I/O modules, MVS, and communi-
cations card.

Loop/Source:

Normally 23 Vdc minimum provided

for transmitter power at the “+T” terminals (25 mA
maximum) and at the “A” terminals on the modular
I/O channels.

ANALOG INPUTS (BUILT-IN)

Quantity/Type:

1 or 2 single-ended voltage-sense

(current loop if scaling resistor is used).

Terminals:

“+T” loop power, “+” positive input, “-”

negative input (common).

Voltage:

0 to 5 Vdc, software configurable. 4 to 20

mA, with a 250 ohm resistor installed across terminals
“+” and “-”.

ANALOG INPUTS (CONTINUED)

Accuracy:

0.1% over operating temperature range.

Impedance:

One megohm.

Filter:

Double-pole, low-pass.

Resolution:

12 bits.

Conversion Time:

30 microseconds.

PULSE INPUT (BUILT-IN)

Sample Period:

50 ms minimum.

Quantity/Type:

1 high-speed source or isolated

pulse counter input when PI jumper is set.

Terminals:

“+T” source power, “+” positive input, “-”

negative input (common).

Voltage:

8 to 30 Vdc (ON state); 0 to 4 Vdc (OFF

state).

Frequency:

10 kHz maximum.

Sample Period:

50 ms minimum.

MVS INTERFACE

Type:

High-speed, multi-drop, serial interface with

power for as many as 4 MVS units located up to 4000
feet from the FloBoss.

Terminals:

“A” and “B” for data; “+” and “-” for power.

Polling Period:

1 sec max.

I/O MODULES (OPTIONAL)

Four slots provided for optional I/O modules. Any

type and combination of I/O modules can be used.

FRONT-PANEL USER INTERFACE

Display:

2 line by 20 character LCD. Overall size is

0.75 by 3.25 inches.

Keypad:

15 multi-function, membrane keys. Keys

allow numerical entries.

ENVIRONMENTAL

Operating Temperature:

-40 to 75 °C (-40 to 167

°F), excluding display, which is -20 to 70 °C (-4 to
158 °F).

Storage Temperature:

-50 to 85 °C (-58 to

185 °F).

Operating Humidity:

To 95% non-condensing.

Vibration:

Less than 0.1% effect on overall accu-

racy when tested to SAMA PMC 31.1, Section 5.3,
Condition 3.

ESD Susceptibility:

Meets IEC 801-2, Level 3.

EMI Susceptibility:

Meets IEC 801-4, Level 4.

RFI Susceptibility:

No effect on operation of unit

when tested per SAMA PMC 33.1 in field classified
as 3-abc with field strength of 30 V/m, circuit board
properly mounted, and doors closed.

Содержание Fisher FLOBOSS 407









































































































































































































Результаты поиска

Содержание Fisher FLOBOSS 407

Отзывы:

Похожие инструкции для Fisher FLOBOSS 407

Бренды по названию

Популярные бренды

Emerson Fisher FLOBOSS 407, Инструкция по эксплуатации

Результаты поиска

Содержание Fisher FLOBOSS 407

Отзывы:

Похожие инструкции для Fisher FLOBOSS 407

Бренды по названию

Популярные бренды