Emerson Fisher FLOBOSS 407 Скачать руководство пользователя страница 169 | Manualshive

Страница: 169 / 200

background image

FloBoss 407 Instruction Manual

Rev 5/00

B-13

B.5 CONFIGURATION

Use the ROCLINK Configuration Software to configure the MVS. The first step in configuring an
MVS is to set the interface address. This is essential if there is more than one MVS connected to a
FloBoss 407 (called a multi-drop configuration), as explained below.

The MVS interface address is set by means of an address parameter by using the ROCLINK Configu-
ration Software. All MVS units are sent from the factory with a default interface address of “1”. This
allows for first-time communications to be accomplished. Do not use address 240 in multi-drop
applications, since all MVS devices with this address will try to respond to requests from the FloBoss.

To configure a multi-drop MVS setup, connect each MVS to the FloBoss 407 one at a time. Ensure
that each MVS is functioning correctly before installing the next MVS.

CAUTION

Before connecting or disconnecting an MVS, remove all power from the MVS,
either by pulling out the MVS connector (plug P8) on the FloBoss 407, or by
unplugging the power to the FloBoss 407. If you do not remove ALL power from
the MVS, electronic components may be destroyed. Refer to Section 2.5.2, Backup
Procedure Before Removing Power.

NOTE

For Measurement Canada units, maintenance and resealing of the FloBoss must
be performed by authorized personnel only.

CAUTION

There is a possibility of losing the FloBoss configuration and historical data held in
RAM while performing the following procedure. As a precaution, save the current
configuration and historical data to permanent memory. Refer to Section 2.5.2.

CAUTION

When installing devices in a hazardous area, make sure each device is labeled for
use in such areas. Procedures involving switching power on or off, or procedures
for installing or removing any wiring or components, must be performed only when
the area is known to be non-hazardous.

CAUTION

To avoid circuit damage when working with the unit, use appropriate electrostatic
discharge precautions, such as wearing a grounded wrist strap.

«
...
167
168
169
170
171
...
»

Содержание Fisher FLOBOSS 407









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Fisher FLOBOSS 407

Бренд: BADLANDS Страницы: 2

Бренд: Bang & Olufsen Страницы: 36

Бренд: Mad Catz Страницы: 4

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 60

Бренд: Danfoss Страницы: 20

Бренд: QUAD Страницы: 17

Бренд: fadini Страницы: 16

Бренд: Samson Страницы: 73

VARIVENT D Series

Бренд: GEA Страницы: 78

Бренд: GEA Страницы: 96

Бренд: GEA Страницы: 66

Бренд: UNI Страницы: 21

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 13

Бренд: IFM Страницы: 49

Бренд: Maestra Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды