182
Cause
1. L’aiguille n’est pas correctement enfilée.
2. Le fil d’aiguille est trop tendu.
3. L’aiguille est tordue ou émoussée.
4. L’aiguille est mal insérée.
5. Le fil de l’aiguille et le fil de la canette ne sont pas correctement placés sous
le pied presseur (tirés vers l’arrière du pied presseur) au début de la couture.
6. Le tissu n'est pas tiré vers l'arrière une fois la couture terminée.
7. Le fil est trop épais ou trop fin pour l’aiguille.
8. Le fil est emmêlé autour de la bobine.
1. Le fil de canette est mal enfilé dans la boîte à canette.
2. Il y a une accumulation de peluches dans la boîte à canette.
3. La canette est endommagée et ne tourne pas correctement.
1. L’aiguille est mal insérée.
2. L’aiguille est tordue ou émoussée.
3. La vis du pince-aiguille est desserrée.
4. Le fil d’aiguille est trop tendu.
5. Le tissu n'est pas tiré vers l'arrière une fois la couture terminée.
6. L’aiguille est trop fine pour le tissu utilisé.
7. Le pied presseur utilisé n’est pas le bon.
1. L’aiguille est mal insérée.
2. L’aiguille est tordue ou émoussée.
3. L’aiguille et/ou le fil ne conviennent pas au tissu utilisé.
4. La machine n’est pas équipée d’une aiguille adéquate pour les tissus
extensibles, très fins ou synthétiques.
5. Le fil d’aiguille n’est pas bien enfilé.
6. La pression du pied n'est pas réglée correctement.
7. L’aiguille utilisée n’est pas adaptée.
1. Le fil d’aiguille est trop tendu.
2. Le fil n’est pas monté correctement sur la machine.
3. L’aiguille est trop grosse pour le tissu utilisé.
4. Le point est trop long pour le tissu.
5. La pression du pied n'est pas réglée correctement.
Placer un stabilisateur léger sous les tissus fins.
1. La pression du pied n'est pas réglée correctement.
2. Le pied presseur utilisé n’est pas le bon.
1. La griffe d’entraînement est remplie de peluches.
2. La pression du pied n'est pas réglée correctement.
3. Les points sont trop courts.
4. Les griffes d'entraînement n'ont pas été relevées après avoir été abaissées.
5. Le pied presseur utilisé n’est pas le bon.
1. Le fil d’aiguille est trop tendu.
2. L’aiguille est trop grosse ou trop petite pour le fil.
3. Les points sont trop longs par rapport à l’épaisseur du tissu.
1. La machine n’est pas branchée.
2. Un fil est bloqué dans la zone du crochet ou dans le mécanisme du coupe-fil
automatique.
3. Le pied presseur est en position relevée.
1. La vis de réglage fin est mal réglée.
2. Le pied presseur utilisé n’est pas le bon.
3. Le fil d’aiguille est trop tendu.
4. La longueur de point ne convient pas au tissu.
5. Utiliser un entoilage ou un stabilisateur pour les tissus fins ou extensibles.
1. La longueur de point ne convient pas au tissu.
2. Un entoilage n'est pas utilisé avec les tissus.
3. Il reste un espace entre le coulisseau et le support de ressort.
4. Le levier de boutonnière n’est pas abaissé.
1. Des fils sont coincés dans la zone du crochet.
2. Il y a une accumulation de peluches dans la boîte à canette ou dans la zone du
crochet.
1. La pression du pied n'est pas réglée correctement.
2. Le pied presseur utilisé n’est pas le bon.
1. Le pied presseur a été relevé avant que le coupe-fil automatique n’ait fini de
travailler.
2. Des fils sont emmêlés dans le mécanisme du coupe-fil automatique.
See page(s)
53-57
39
45
43
59
61
43
47
51
167-169
changez la canette
45
45
45
39
61
45
31
45
45
45
43
53-57
27
43
39
51-57
45
19
27
27
31
167-169
27
19
29
31
35
45
19
15
167-169
Abaisser le pied.
41
31
39
19
Utilisez un stabilisateur.
19
85
93
87
167-169
167-169
27
31
63
167-169
Anomalie
Le fil d’aiguille
casse.
Le fil de canette
casse.
L’aiguille casse.
Points sautés.
La couture fronce.
Le tissu glisse.
Le tissu n’avance
pas en douceur.
Fronces
La machine ne
fonctionne pas.
Les points sont
déformés.
Les boutonnières
avec détecteur ne
fonctionnent pas.
Fonctionnement
bruyant.
Les épaisseurs de
tissu se décalent.
La DEL du coupe-fil
automatique
clignote.
Résolution des problèmes
Vous entendrez peut-être un léger bourdonnement provenant des moteurs à l’intérieur de la machine. Ce bruit est normal
et ne doit pas être source d’inquiétude.