Elitech NANODUCT 1030 Скачать руководство пользователя страница 9

Страница: 9 / 71

Section 1: Introduction

WARNING!
Consult a physician before performing a test on patients who have had previous adverse reactions

to electrotherapy.

WARNING!
The lithium coin cell backup battery used to power the clock is not accessible to the user and

should only be replaced by qualified service personnel.

CAUTION:
A Nanoduct sweat analysis test should be carried out at a time when the patient is clinically stable,

well-hydrated, free of acute illness, and not receiving mineralocorticoids.

CAUTION:
Consult a physician before performing multiple tests on a patient within a 24-hour period.

CAUTION:
Pilogel discs should be refrigerated at 2 °C to 10 °C. DO NOT FREEZE. Never use discs that have

been frozen or that are cracked.

CAUTION:
This equipment has been designed and tested to EN 55011/CISPR 11 Group 1 Class B and FCC CFR

47 Part 15 Class B. In a domestic environment it may cause radio interference, in which case, the

operator may need to take measures to mitigate the interference.

CAUTION:

Only spare parts and accessories supplied or specified by ELITechGroup should be used with this

device. Using non-approved parts may affect the performance and safety features of the device.

If the device is used in a manner not specified by ELITechGroup, the protection provided by the

device may be impaired. If in doubt, contact an ELITechGroup representative.

CAUTION:
The USB connection on the device is intended to be used by authorized personnel. For security

purposes, it is recommended to execute a virus/malware scan on any computers prior to making

connection. Do not connect to a line powered computer when the instrument is attached to a

patient.

Содержание NANODUCT 1030








































































Результаты поиска

Содержание NANODUCT 1030

Отзывы:

Бренды по названию

Популярные бренды

Elitech NANODUCT 1030, Руководство пользователя

Результаты поиска

Содержание NANODUCT 1030

Отзывы:

Бренды по названию

Популярные бренды