Elitech NANODUCT 1030 Скачать руководство пользователя страница 33

Страница: 33 / 71

Section 3: Sweat Induction and Analysis

C. Once current has reached the full 0.5 mA, that level is maintained for 2

minutes. The display shows “Full Current” and a time bar at the bottom of

the screen shows progress.

D. Current then decreases to zero (indicated by a short beep). The display

shows “Complete” and “ENTER To Continue.”

Press ENTER to return to the main menu.

9 Remove the Red Electrode

While applying pressure to the red electrode with the index finger, rotate the

upper ring approximately 90° clockwise until the cutouts align with the electrode

flanges. Then remove the electrode. Immediately and properly dispose of the

Pilogel disc from the positive (red) electrode.

CAUTION
Do not disturb or remove the red holder. It must remain in place during

analysis. In addition, leave the negative (black) electrode, gel, holder and

tape-downs in position to provide a ground contact for initial sweat rate

determination.
WARNING!
Pilogel is considered harmful. Do not ingest. Consult the SDS sheet for

more information.
WARNING!
Pilogel discs are a potential choking hazard. Make sure they are disposed

of properly.

10 Clean and Dry the Skin in the Collecting Area

Use a cotton swab with a small amount of DI water to clean the entire skin area

inside the holder, followed by clean dry swabs to completely dry the area. Without

delay, proceed to the next step.

NOTE:

If the sensor is not inserted immediately, repeat the cleaning and drying

procedure just before attaching the sensor.

Iontophoresis

Full

Current

Iontophoresis

ENTER To Continue

Full

Current

Complete

Содержание NANODUCT 1030








































































Результаты поиска

Содержание NANODUCT 1030

Отзывы:

Бренды по названию

Популярные бренды

Elitech NANODUCT 1030, Руководство пользователя

Результаты поиска

Содержание NANODUCT 1030

Отзывы:

Бренды по названию

Популярные бренды