Elitech NANODUCT 1030 Скачать руководство пользователя страница 66

Страница: 66 / 71

Medical Electrical Equipment, in general, needs special precautions regarding EMC and needs to be used

according to the EMC information provided in the accompanying documents. Portable and mobile RF

communications equipment can affect Medical Electrical Equipment.

The Nanoduct instrument is not susceptible to some types of electrical interference, because it is battery-

powered and doesn’t connect to power lines that might conduct high frequency noise along with the power.

However, it could be affected by radio emissions from other devices. Like all digital electronic equipment,

it also emits some radio frequency energy when it operates. Use of accessories or cables other than those

supplied with the Nanoduct or supplied by the manufacturer as replacement parts could result in increased

emissions or decreased immunity of the Nanoduct.
The tables below show the test results for both EMC emissions and immunity.

Guidance and Manufacturer’s Declaration – Electromagnetic Emissions

The Nanoduct system is intended for use in the electromagnetic environment specified below. The customer or the

user of the Nanoduct system should assure that it is used in such an environment.

Emissions Test

Compliance

Electromagnetic Environment - Guidance

RF Emissions

CISPR 11

Group 1

The Nanoduct system uses RF energy only for its internal

function. Therefore, its RF emissions are very low and are not

likely to cause any interference in nearby electronic equipment.

RF Emissions

CISPR 11

Class B

The Nanoduct system is suitable for use in all establishments

including domestic. It is battery-powered and does not connect

to the public power supply network.

The Nanoduct system should not be used adjacent to or stacked with other equipment. If adjacent or

stacked use is necessary, the Nanoduct system should be observed to verify normal operation in the

configuration in which it will be used.

Guidance and Manufacturer’s Declaration – Electromagnetic Immunity

The Nanoduct system is intended for use in the electromagnetic environment specified below. The customer or the

user of the Nanoduct system should assure that it is used in such an environment.

Immunity Test

IEC 60601-1-2 Test Level

Compliance Level

Electromagnetic Environment -

Guidance

Electrostatic

discharge (ESD)

IEC 61000-4-2

+/- 2, 4, 8 kV contact
+/- 2, 4, 8, 15 kV air

+/- 8 kV contact
+/- 15 kV air

The Nanoduct system is isolated

from ground. Any typical flooring may

be used.

Appendix J: Electromagnetic Compatibility (EMC)

Содержание NANODUCT 1030








































































Результаты поиска

Содержание NANODUCT 1030

Отзывы:

Бренды по названию

Популярные бренды

Elitech NANODUCT 1030, Руководство пользователя

Результаты поиска

Содержание NANODUCT 1030

Отзывы:

Бренды по названию

Популярные бренды