Elitech NANODUCT 1030 Скачать руководство пользователя страница 45

Страница: 45 / 71

Section 4: Troubleshooting and Preventive Maintenance

Error Message

Displayed

Screen

Probable Causes / Possible Solutions

High Resistance

Fault

Moisten Skin

Iontophoresis

Probable Causes:

No Pilogel discs under electrodes.

Dirty electrodes.

Electrodes not properly latched with locking ring or cable

becoming detached from Nanoduct.

Holders not adequately secured to patient.

Damaged electrode cable assembly.

Patient’s skin resistance is too high for proper

iontophoresis current.

Possible Solutions:

Ensure that a Pilogel disc is under each electrode.

Clean electrodes if necessary. Place a drop of deionized

water directly on the clean skin beneath each Pilogel disc.

Ensure both electrodes are latched with locking ring and

that the cable is properly connected to the Nanoduct.

Ensure holders are secured with adequate tightness to

the patient’s limb. Do not overtighten and impede blood

circulation.

Inspect the electrode cable assembly for any damage.

Do not use electrodes if there is any damage to the cable

insulation or if there are exposed bare wires. Replace

electrode cable assembly.

Repeat the sweat test one time.†

If fault continues to occur, contact ELITechGroup for further

instructions.

Fault

Check Instrument

Iontophoresis

Probable Causes:

Operational error has been encountered by the system.

Possible Solutions:

Reset the Nanoduct.*

Perform a Self Test on the Nanoduct.

If the problem persists, discontinue use of the Nanoduct and

contact ELITechGroup for further instructions.

Over Current

Fault

Check Instrument

Iontophoresis

Probable Causes:

Iontophoresis current exceeds allowed threshold.

Nanoduct may be damaged. Discontinue use of the

Nanoduct.

Possible Solutions:

Contact ELITechGroup for further instructions.

Содержание NANODUCT 1030








































































Результаты поиска

Содержание NANODUCT 1030

Отзывы:

Бренды по названию

Популярные бренды

Elitech NANODUCT 1030, Руководство пользователя

Результаты поиска

Содержание NANODUCT 1030

Отзывы:

Бренды по названию

Популярные бренды