manualshive.com logo in svg

Elitech NANODUCT 1030, Руководство пользователя

Поделиться
Скачать
Elitech NANODUCT 1030 Скачать руководство пользователя страница 52

52

Instrument 

Specifications

Readout

128 x 64 LCD graphic display (non-backlit). Supports up to 8 lines 

of 18 characters or numerals, with multi-lingual support (English, 

French, German, and Spanish).

Sound

Alert signals.

Keyboard

ON, OFF, SELECT and ENTER keys.

Electrode Connection 

6-pin locking medical connector to mate with induction/conductivity 

cell, cable.

Serial Outputs

RS-232 

(ASCII format)

9-pin D-Sub male connector.

Data Protocol: 9600 Baud, 1 Start Bit, 8 Data Bits, No Parity, 1 Stop 

Bit.

Pin #

Signal

Description

1

N/C

No Connection

2

RXD

Receive Data (output)

3

TXD

Transmit Data (input)

4

N/C

No Connection

5

GND

Signal Ground

6

N/C

No Connection

7

N/C

No Connection

8

CTS

No Connection

9

N/C

No Connection

USB

 – Device

Type B Receptacle.

Electrical

Four AA Alkaline batteries (NEDA 15A, IEC LR6). 

Typical solid-state, over-current circuit protection. 
3.0 VDC lithium coin cell for the real time clock. Expected battery 

life of lithium cell is >5 years.

Sweat Induction Control 

Current profile controlled for use with Pilogel Discs for Nanoduct 

(or fiber pilocarpine reservoirs) with multiple fail-safe circuits to limit 

current. Nominal current is 0.5 (± 0.02) mA for 120 (±2) seconds. 

Total iontophoresis time is ~2.5 minutes including current ramping. 

Maximum fail-safe current limited to <4 mA.

Real Time Clock 

± 2 minutes per year (battery backed).

Operating Temperature 

15 to 30 °C (59 to 86 °F).

Operating Relative Humidity

≤ 85%, non-condensing.

Operating Atmospheric Pressure

≥ 79.5 kPa (≤ 2000 m).

Storage Temperature

0 to 60 °C (32 to 140 °F).

Appendix A: 

Instrument Specifications

Содержание NANODUCT 1030








































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды