manualshive.com logo in svg

Elitech NANODUCT 1030, Руководство пользователя

Поделиться
Скачать
Elitech NANODUCT 1030 Скачать руководство пользователя страница 18

18

18

Section 1: Introduction

Serial Data Ports

RS-232 Port

The Nanoduct RS-232 port uses a DB9 connector located on the top of the 

instrument. This port is for asynchronous serial communication with a printer or 

computer. The RS-232 port can be used to print out results of sweat tests (with a 

time and date stamp). Data output is in ASCII characters. Refer to Appendix C for 

additional information.

WARNING!
Electrical shock hazard. Never connect to a line powered printer or 

computer when the instrument is attached to a patient.

USB Port 

The Nanoduct Universal Serial Bus (USB) port uses a standard USB type-B 

receptacle. The port is configured as a USB device (not a host). Data output is 

in ASCII characters. The USB port allows the updating of firmware in the field 

and allows a reading to be transferred to the Nanoduct Lab Report application. 

The port cannot be used with a USB printer. Refer to Appendix C for additional 

information.

WARNING!
Electrical shock hazard. Never connect to a line powered printer or 

computer while the instrument is attached to a patient. 

 

Содержание NANODUCT 1030








































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды