Elitech NANODUCT 1030 Скачать руководство пользователя страница 55

Страница: 55 / 71

RS-232 Serial Port

WARNING!
Do not connect a line powered printer or computer when the instrument is attached to a patient.

The Nanoduct RS-232 port uses a DB9 connector located on the top of the instrument. This port is for

serial communication with a printer. Data is automatically sent out on the serial port whenever “Recall

Reading” or “Check Controls” is selected from the main menu. Data output is in ASCII characters. The

following are examples of the data printed.

Data from the recall Reading selection:

2009-10-20 14:24

41 MMOL/L EQ NACL

Data from the Check Controls menu selection:

CAL2009-10-19 12:15

80 mmol/L eq NaCl

Data from the Self Test mode:

2009-10-19 12:15

PRINT TEST

Data from the Recall Reading menu includes the date, time, and result from the last completed sweat test.

Data from the Check Controls Menu includes the prefix CAL followed by the date, time, and calibration

value from the last calibration. If a new calibration occurs, the new date, time, and calibration values are

sent to the printer. Data from the Self Test mode includes the date, time, and the text “Print Test.”

Connecting to a Printer

The serial port is configured as Data Communications Equipment (DCE), however the 9-pin connector is

male instead of the traditional female connector. The required cable is null-modem with a male connector

on one end and a female connector on the other. We recommend that you purchase the ELITechGroup

Printer Cable (AC-049).

Data protocol: 9600 Baud, 1 Start Bit, 8 Data Bits, No Parity, 1 Stop bit.

USB Port

WARNING!
Electrical Shock Hazard. Do not connect to a line powered computer when the instrument is

attached to a patient.

The Nanoduct has a Universal Serial Bus (USB), used in conjunction with Nanoduct Lab Report software

to record data from the Nanoduct. The port is configured as a USB device (not a host) and uses a standard

USB type receptacle. The port cannot be used with a USB printer. Always install the Nanoduct Lab Report

software before connecting the Nanoduct to a computer. This allows the computer to correctly recognize

the Nanoduct when it is connected. Refer to the Nanoduct Lab Report Manual for additional information.

Appendix C: Serial Data Ports

Содержание NANODUCT 1030








































































Результаты поиска

Содержание NANODUCT 1030

Отзывы:

Бренды по названию

Популярные бренды

Elitech NANODUCT 1030, Руководство пользователя

Результаты поиска

Содержание NANODUCT 1030

Отзывы:

Бренды по названию

Популярные бренды