manualshive.com logo in svg

Elitech NANODUCT 1030, Руководство пользователя

Поделиться
Скачать
Elitech NANODUCT 1030 Скачать руководство пользователя страница 21

21

2.1  Installing or Replacing the Batteries

1. The battery compartment is on the back of the instrument. Turn the 

instrument so that the back is facing up. Using a Phillips screwdriver, 

remove the two screws that are holding the battery door in place. Remove 

the battery door. 

2. Insert four fresh alkaline AA batteries (ANSI/NEDA 15A, IEC LR6) making 

sure that each battery is inserted with the correct orientation as shown. 

There are markings within the battery holder that show proper orientation of 

the batteries. 

3. Reposition the battery door and insert the screws. Using a Phillips 

screwdriver, tighten the two screws that hold the door in place.

4. Dispose of the spent batteries according to battery manufacturer’s 

instructions and local regulations.

NOTE: 

Batteries are installed in the instrument at the time of shipment. Unless 

the Low Battery message displays, the batteries do not need to be replaced. 

If you are not using the instrument for an extended period of time, remove the 

batteries. Batteries can leak and damage terminals if left unused for extended 

periods.

WARNING!

Do not install batteries backwards, charge, put in fire or mix with other 

battery types. Batteries may explode or leak causing injury. Replace all 

batteries at the same time.

Section 2: Initial System Setup

Содержание NANODUCT 1030








































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды