manualshive.com logo in svg

Elitech NANODUCT 1030, Руководство пользователя

Поделиться
Скачать
Elitech NANODUCT 1030 Скачать руководство пользователя страница 27

Section 2 : Initial System Setup

27

3. Connect the electrodes by placing a Pilogel disc in each holder and then 

holding the two discs together between two fingers to check the current. 

The current should read approximately 0.5 mA. The instrument continues to 

read and display the electrode current reading. Current that continually 

decreases is an indication of low or weak batteries. Press ENTER to 

continue with the Self Test.

4. Connect to the calibration plate to check for proper operation. The display 

should read the value of the calibration point that the cable is connected to. 

For example, if connected to the 80 mmol/L calibration point, then the 

reading on the display should be 80 mmol/L.

5. Connect to the printer to test the serial communication. Press SELECT to 

send data out the serial port. The date and time are sent out the port along 

with the message “PRINT TEST” each time SELECT is pressed.

 

Press ENTER to return to the SETUP MENU.

Self Test Mode

ENTER To Continue

Connect Electrodes

To Check Current

#.### m.A.

 

Self Test Mode

ENTER To Continue

Connect To

Calibration Plate

To Check Operation

80 mmol/L eq NaCl

 

2019-04-21 15:24 
PRINT TEST

Self Test Mode

ENTER To Continue

Connect To Printer

SELECT Key

To Test Serial

Communication

 

Содержание NANODUCT 1030








































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды