Edwards D397-50-000 Скачать руководство пользователя страница 27

Страница: 27 / 76

Page 21

Edwards and the Edwards logo are trademarks of Edwards Limited.

Operation

D397-50-880 Issue C

4.7.1

Software module 852 - DX Pump Control

General Description

Main DX Pump control and monitoring module. This module must be selected for pump control.

Output bytes (from Master)

Input bytes (to Master)

Associated Parameter options

None.

Table 15 - DX status flags

1st

Stop if value 0. Run if value 1.

1st

Form a 16-bit number, which is the motor speed in Revolutions per
Second. (0-1800).

2nd

3rd

Form a 32-bit system status word. The Upper two bytes (3rd and
4th) are reserved. Each bit of lower 2 bytes is a flag. To decode
the status first convert the value to binary. Refer to

Table 15

to interpret each bit.

4th
5th
6th

Bit No.

Status Flag Name

Meaning if Flag 0

Meaning if Flag 1

Fail

Not failed

Failure condition

Stopped Speed

Pump in motion

Pump at rest

Normal Speed

Below normal speed

Above normal speed

Vent valve

Valve output not powered

Valve output powered

Start

Not commanded to start

Commanded to start

Serial Enable

Serial control disabled

Serial control enabled

Standby

Standby not commanded

Standby commanded

50% speed

Below 50% speed

Above 50% speed

Parallel control

Not in Parallel control mode

In Parallel control mode

Serial control

Not in Serial control mode

In Serial control mode

Software Compatibility Podule software not mis-matched Invalid Podule software

Software Completion

Podule upload complete

Podule Config or Cal failed

Timer State

Timer duration not exceeded

Timer (for 50% speed) expired

Hardware Trip

No trip

Overspeed or Overcurrent trip

Thermistor Error

Internal temp system good

Internal temp system failed

Serial Interlock

Serial enable good

Serial enable bad

Содержание D397-50-000








































































Результаты поиска

Содержание D397-50-000

Отзывы:

Похожие инструкции для D397-50-000

Бренды по названию

Популярные бренды

Edwards D397-50-000, Инструкция по эксплуатации

Результаты поиска

Содержание D397-50-000

Отзывы:

Похожие инструкции для D397-50-000

Бренды по названию

Популярные бренды