Edwards D397-50-000 Скачать руководство пользователя страница 35

Страница: 35 / 76

Page 29

Edwards and the Edwards logo are trademarks of Edwards Limited.

Operation

D397-50-880 Issue C

Associated Parameter options

4.8.9

Software module 905 - Turbo Pump Speed

This module can be used with any Turbo pump that is compatible with a TIC unit.

General Description

Monitors speeds and sets failures times.

Output bytes (from Master)

None.

Input bytes (to Master)

Associated Parameter options

Note:

A DX pump does not use these options, it uses 853 instead; leave at default values for DX.

Bytes

Parameter Option

Description of Parameter

1st

Module number

Cannot be changed.

2nd

3rd

Control gauge

Allows the turbo pump operation to be controlled by one of
the gauges if desired. Options include none, but if this option
is selected it is recommended that the enable option is set to
disabled.

4th

5th

Gauge units

Setpoint units. Options are Pascals or volts.

6th

Turbo setpoint ON

These are four byte numbers in IEEE-754 format. A conversion
utility must be used. See note in

Section 4.8.17

7th
8th
9th

10th

Turb setpoint OFF

These are four byte numbers in IEEE-754 format. A conversion
utility must be used. See note in

Section 4.8.17

11th
12th
13th
14th

Control enable

Enables or disables control at the chosen setpoint by the
chosen gauge.

15th

Start delay

In minutes from zero to 99.

1st

This is a signed word. The pump speed in 200th's of percent.

2nd

3rd

Alert - refer to table in Appendix A2.

4th

Priority - refer to table in Appendix A3.

Bytes

Parameter Option

Description of Parameter

1st

Module number

Cannot be changed.

2nd

3rd

Start/fail time in minutes
(1-30).

This is the time allowed from start to reach 50% speed. If the
speed is not reached in this time a failure condition is
entered.

4th

Droop fail time in minutes
(0-30).

This is the time allowed for the speed to drop below 50%. If
the speed is below 50% for longer than this time a failure
condition is entered.

Содержание D397-50-000








































































Результаты поиска

Содержание D397-50-000

Отзывы:

Похожие инструкции для D397-50-000

Бренды по названию

Популярные бренды

Edwards D397-50-000, Инструкция по эксплуатации

Результаты поиска

Содержание D397-50-000

Отзывы:

Похожие инструкции для D397-50-000

Бренды по названию

Популярные бренды