Edwards D397-50-000 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 76

background image

© Edwards Limited 2010. All rights reserved.

Page 39

Edwards and the Edwards logo are trademarks of Edwards Limited.

Operation

D397-50-880 Issue C

4.9

Response time calculations & Measurements

The TIC & DX pump Profibus units response times (due to a change in output data) and true data update times vary
significantly depending on the data exchange configuration and the attached equipment. For both unit types there
is also a time delay due to the bus speed. For 9.6Kbd this is approximately 50ms. For 19.2Kdb it is approximately
25ms. For all other bus speeds the delay is relatively negligible.

For a DX pump Profibus unit on a high speed network, the response time on average is roughly:

120ms for the first software module
+ 30ms extra for each additional configured software module.

For a TIC Profibus unit on a high speed network, the response time on average is roughly:

30 ms
+ 30ms extra for each configured software modules with a 900 number
+ 140ms extra for each configured software modules with a 800 number
+ 50ms extra if a DX turbo pump is attached
+ 300ms extra if the measure of response time is gauge pressure update time.

Example: A TIC Profibus module fitted to a network operating at 19.2Kbd with a DX pump and 2 gauges fitted, with
the configuration 913, 914, 904, 860. To determine the likely average gauge update rate the calculation is

25ms (for bus speed)
+ 50ms (for Dx pump)
+ 30ms (fixed)
+ 3 x 30ms = 90 ms (for 900 modules)
+ 140ms (for 800 module)
+ 300ms (for gauge update time as the measure)
= 635ms

Note:

The Sync and Freeze Profibus functions are supported by the TIC & DX pump Profibus units, but should be
used with caution due to the variable time delays associated with the units.

«
...
43
44
45
46
47
...
»

Содержание D397-50-000













































































Отзывы:

Нет отзывов

Похожие инструкции для D397-50-000

Relion 670 series

Бренд: ABB Страницы: 760

Бренд: ABB Страницы: 128

Бренд: Value Point Страницы: 7

Бренд: Daikin Страницы: 48

Бренд: Daikin Страницы: 77

Бренд: Daikin Страницы: 32

Бренд: Daikin Страницы: 46

Бренд: Daikin Страницы: 14

Бренд: Daikin Страницы: 16

Бренд: Daikin Страницы: 1

Бренд: GARAN Страницы: 8

Бренд: Gamma Vacuum Страницы: 25

Бренд: Gamma Страницы: 28

Бренд: Xylem Страницы: 48

Бренд: Radionics Страницы: 14

Бренд: Osram Страницы: 3

Бренд: Delta Страницы: 16

Бренд: D+H Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды