Edwards D397-50-000 Скачать руководство пользователя страница 28

Страница: 28 / 76

D397-50-880 Issue C

Page 22

Edwards and the Edwards logo are trademarks of Edwards Limited.

Operation

4.7.2

Software module 853 - DX Pump Set-up

There are two versions of this module for the two types of DX pumps - 75DX and 255DX. The software modules have
different power limit values. The correct module for the pump in use must be selected.

General Description

DX Pump set-up and configuration.

Output bytes (from Master)

None.

Input bytes (to Master)

Associated Parameter options

4.7.3

Software module 859 - DX Pump Temperatures

General Description

Read DX Pump controller and motor temperatures.

Output bytes (from Master)

None.

Input bytes (to Master)

Associated Parameter options

None.

1st

Dummy byte (always zero).

Bytes

Parameter Option

Description of Parameter

1st

Module number

Cannot be changed.

2nd

3rd

Vent options

8 options with textual descriptions. More information
available on each option from the DX pump manual.

4th

Ramp and droop timer
setting

Value of the timeout period for both initial speed ramp-up and
if the speed drops below 50%. Value is in minutes (1-30).

5th

Power limit

Sets the maximum power that the DX pump motor will be
allowed to consume (in Watts). The range is different for the
two pump types.

6th

Effect if speed drops below
50%

Options are stop immediately or stop if timing period
exceeded.

7th

Brake use

Whether Electronic braking is enabled or disabled.

1st

Motor temperature in °C.

2nd

Controller temperature in °C.

Содержание D397-50-000








































































Результаты поиска

Содержание D397-50-000

Отзывы:

Похожие инструкции для D397-50-000

Бренды по названию

Популярные бренды

Edwards D397-50-000, Инструкция по эксплуатации

Результаты поиска

Содержание D397-50-000

Отзывы:

Похожие инструкции для D397-50-000

Бренды по названию

Популярные бренды