Edwards D397-50-000 Скачать руководство пользователя страница 32

Страница: 32 / 76

D397-50-880 Issue C

Page 26

Edwards and the Edwards logo are trademarks of Edwards Limited.

Operation

4.8.2

Software module 853 - DX Pump Set-up

This module must only be selected if a DX pump is connected to the TIC.

Note:

Two versions of this module exist for both types of DX pumps - 75DX and 255DX. The software modules have
different power limit values. The correct module must be selected.

General Description

DX Pump set-up and configuration.

Output bytes (from Master)

None.

Input bytes (to Master)

Associated Parameter options

4.8.3

Software module 859 - DX Pump Temperatures

This module must only be selected if there is a DX pump connected to the TIC.

General Description

Read DX Pump controller and motor temperatures.

Output bytes (from Master)

None.

Input bytes (to Master)

Associated Parameter options

None.

1st

Dummy byte (always zero).

Bytes

Parameter Option

Description of Parameter

1st

Module number

Cannot be changed.

2nd

3rd

Vent options

8 options with textual descriptions. More information
available on each option from the DX pump manual.

4th

Ramp and droop timer
setting

Value of the timeout period for both ramp time and droop
time. Value is in minutes (1-30).

5th

Power limit

Sets the maximum power that the DX pump motor will be
allowed to consume (in Watts). The range is different for the
two pump types.

6th

Effect if speed drops below
50%

Options are stop immediately or stop if timing period
exceeded.

7th

Brake use

Whether Electronic braking is enabled or disabled.

1st

Motor temperature in °C.

2nd

Controller temperature in °C.

Содержание D397-50-000








































































Результаты поиска

Содержание D397-50-000

Отзывы:

Похожие инструкции для D397-50-000

Бренды по названию

Популярные бренды

Edwards D397-50-000, Инструкция по эксплуатации

Результаты поиска

Содержание D397-50-000

Отзывы:

Похожие инструкции для D397-50-000

Бренды по названию

Популярные бренды