Edwards D397-50-000 Скачать руководство пользователя страница 29

Страница: 29 / 76

Page 23

Edwards and the Edwards logo are trademarks of Edwards Limited.

Operation

D397-50-880 Issue C

4.7.4

Software module 860 - DX Pump Power

General Description

Read DX Pump motor power consumption.

Output bytes (from Master)

None.

Input bytes (to Master)

Associated Parameter options

None.

4.7.5

Software module 869 - DX Pump Speed Demand

General Description

Controls DX Pump speed demand (value).

Output bytes (from Master)

Input bytes (to Master)

None.

Associated Parameter options

4.7.6

Software module 875 - DX Vent Valve close

General Description

Forces vent valve closed (by powering it) regardless of vent valve control set-up.

Output bytes (from Master

)

Note:

Once a "forced close" command has been sent it can only be cleared in the DX pump podule by demanding
the pump to stop (using software module 852).

Input bytes (to Master)

None.

Associated Parameter options

None.

1st

Forms a 16-bit (signed) number, which is the motor power in 10th’s
of Watts.

2nd

1st

Speed demand (if pump started) is full speed if value 0, and
standby speed if value 1.

Bytes

Parameter Option

Description of Parameter

1st

Module number

Cannot be changed.

2nd

3rd

Normal speed indication

The value as a percentage of the full speed to define normal
speed indication. (50-100%).

4th

Standby speed

The value as a percentage of the full speed to define standby
speed. (55-100%).

1st

Not forced closed if value 0. Forced closed if value 1.

Содержание D397-50-000








































































Результаты поиска

Содержание D397-50-000

Отзывы:

Похожие инструкции для D397-50-000

Бренды по названию

Популярные бренды

Edwards D397-50-000, Инструкция по эксплуатации

Результаты поиска

Содержание D397-50-000

Отзывы:

Похожие инструкции для D397-50-000

Бренды по названию

Популярные бренды