Edwards D397-50-000 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 76

background image

© Edwards Limited 2010. All rights reserved.

Page 3

Edwards and the Edwards logo are trademarks of Edwards Limited.

Technical data

D397-50-880 Issue C

2

Technical data

2.1

Electrical data

Table 1 - Electrical data

Power connector type

2 Way cable-mount Terminal Block (supplied)
Suitable parts include: Phoenix MSTB 2.5/2-ST-5.08;
Weidmuller BLZ 5.08/2; Amp 796634-2; IMO 21.950/2

Electrical supply
    TIC Profibus Module
    DX Pump Profibus Module for
    EXT75DX and EXT255DX

9 V d.c. min to 52 V d.c. max
21.6 V d.c. min to 25.2 V d.c. max

Power consumption

5W maximum
Switch on surge 500 mA max.

Note:

DX Pump Profibus Modules also supply power to
the pump. Additional supply requirement: 6 A
for EXT75DX, 10 A for EXT255DX. Refer to
manuals for other DX Turbo Pumps.

Fuse
TIC Profibus Module
DX Pump Profibus Module

No internal fuse
Fitted with 10 A internal fuse. Suitable fuses available
from Edwards (Part No. D39751830).

WARNING

(DX version only)
Incorporate a suitable isolation device in the electrical supply. Locate the switch in an easily
accessible position and mark it as the disconnecting device for the DX pump. If you do not, you
will not be able to switch off the DX pump in an emergency.

WARNING

Do not exceed the maximum supply voltage. Excessive supply voltage will cause permanent
damage to the control electronics and may result in a mechanical hazard in some failure
conditions.

Profibus cable

Should be screened and comply with EN50170

RS232 cable (TIC version only)

25 m max. Screening not required.

DX pump cable (DX pump version only)

Use (1 m) cable supplied with DX pump only or Edwards
DX pump extension cables.

«
...
7
8
9
10
11
...
»

Содержание D397-50-000













































































Отзывы:

Нет отзывов

Похожие инструкции для D397-50-000

Бренд: Samson Страницы: 100

Бренд: Radio Shack Страницы: 3

Бренд: Campbell Страницы: 8

Бренд: hager Страницы: 62

coviva Smartbox TKP100A

Бренд: hager Страницы: 45

Бренд: Harman Страницы: 2

Бренд: T-Link Страницы: 3

Бренд: Madas Страницы: 6

Бренд: Madas Страницы: 11

IntelliZone2 MasterStat

Бренд: Water Furnace Страницы: 44

Z3-DM8107-SDI-RPS

Бренд: Z3 Technology Страницы: 73

Бренд: Z-Wave Страницы: 14

Бренд: Z-Wave.Me Страницы: 4

Бренд: Dantherm Страницы: 20

Frigolink FVB110B

Бренд: WURM Страницы: 4

Бренд: Samson Страницы: 102

Бренд: Dejero Страницы: 24

Бренд: WINDY NATION Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды