Edgetech 6205S Скачать руководство пользователя страница 47

Страница: 47 / 97

4-30

6205s BATHYMETRIC AND SIDE SCAN SONAR

0020300_REV_E

Figure 4-3: Figure 4 3: 6205S System Is Optimized To Work With A Falling Edge 1PPS Signal

If a falling edge trigger is not available, a rising edge trigger can be used. There are no software or

hardware adjustments required. However, a latency equivalent to the input trigger’s pulse width will be

generated. As a result, we recommend using a pulse width of 1ms or less if a rising edge trigger must be

used. Static latency correction occurs during the patch test process in third party software packages.

4.2.4

Sonar Data Flow

The Discover Bathymetric software acquisition package provides a way to control, store, and display the

bathymetry and side-scan sonar data. Discover Bathymetric contains two sub-modules. This first is the

Bathymetric Processor that processes the bathymetry solutions. The second is the Discover application

that processes and displays the dual-frequency side-scan data. If third-party software is utilized, it would

be added to the data flow. The Sonar Data Flow Chart below (

IGURE

4-3)

illustrates the data flow between

Discover, the Bathymetric Processor, and any third-party software.

NOTE:

The 6205s Sonar Interface Box flow chart can be used in either the

6205s-R Rack Mount Interface Box or 6205s-P Portable Interface Box.

Содержание 6205S


































































































Результаты поиска

Содержание 6205S

Отзывы:

Похожие инструкции для 6205S

Бренды по названию

Популярные бренды

Edgetech 6205S, Руководство пользователя по оборудованию

Результаты поиска

Содержание 6205S

Отзывы:

Похожие инструкции для 6205S

Бренды по названию

Популярные бренды