Edgetech 6205S Скачать руководство пользователя

Страница: 75 / 97

8-58

6205s BATHYMETRIC AND SIDE SCAN SONAR

0020300_REV_E

8.3

Configuring COM Ports

There are three available COM ports on the Interface Box to provide the necessary information to the

6205s. This information includes position (latitude/longitude), heading, attitude (roll, pitch, and heave),

and time. This appendix explains how to configure the three COM ports depending on what type of

sensors are used.

NOTE:

Most of the COM port configuration can and should be completed

via the Discover Bathymetric Software.

8.3.1

One Sensor

One sensor, such as the Applanix PosMV, may be used to supply position (latitude/longitude), heading,

attitude, and a time source. For this type of configuration, only COM1 will be utilized.
To configure the COM ports for one sensor:

Turn on Topside PC and connect the 6205s via the deck cable to the 6205s Topside Interface Box.

Turn on the 6205s Sonar Head and run the Remote Desktop Application, named Sonar. The main

screen, as shown in

FIGURE

8-11,

should appear.

Figure 8-11: Sonar Remote Desktop Application, Main Screen

Here, the user will see the Sonar Application running (designated by the blue arrow). Sonar.exe is

the firmware that controls the system.

Click on the 'X' at the top right to close the firmware.

Double click on the Shortcut to EdgeTech icon and open the SSSonarBathy folder, then Sonar

folder.

Look for the SonarSerial.ini file, as shown in

FIGURE

8-12

, and open it using WordPad or Notepad,

as shown in

FIGURE

8-13

Содержание 6205S


































































































Результаты поиска

Содержание 6205S

Отзывы:

Похожие инструкции для 6205S

Бренды по названию

Популярные бренды

Edgetech 6205S, Руководство пользователя по оборудованию

Результаты поиска

Содержание 6205S

Отзывы:

Похожие инструкции для 6205S

Бренды по названию

Популярные бренды