Eclipse CD 8445E Скачать руководство пользователя страница 76

Страница: 76 / 101

188

Various Settings

When the button is turned, the
frequency changes in the following
order.

This adjusts the frequency level.

[

] button:

Increases level

[

] button:

Decreases level

Each time the button is pressed, the
Q curve changes in the following
order.

The frequencies that have been
adjusted for either the channel or
band cannot be selected.

The preset value is overwritten by
the value set using the above steps.
The time alignment and crossover
adjustments will also be stored at this
time.

Turn the [SEL] button to select
the frequency to be adjusted.

Front1, Front2,
Front3, Rear1,
Rear2, Rear3

63Hz

↔

80Hz

↔

100Hz

↔

125Hz

↔

160Hz

↔

200Hz

↔

250Hz

↔

315Hz

↔

400Hz

↔

500Hz

↔

630Hz

↔

800Hz

↔

1kHz

↔

1.25kHz

↔

1.6kHz

↔

2kHz

↔

2.5kHz

↔

3.15kHz

↔

4kHz

↔

5kHz

↔

6.3kHz

↔

8kHz

↔

10kHz

↔

12.5kHz

↔

16kHz

Front4, Front5,
Rear4, Rear5

200Hz

↔

250Hz

↔

315Hz

↔

400Hz

↔

500Hz

↔

630Hz

↔

800Hz

↔

1kHz

↔

1.25kHz

↔

1.6kHz

↔

2kHz

↔

2.5kHz

↔

3.15kHz

↔

4kHz

↔

5kHz

↔

6.3kHz

↔

8kHz

↔

10kHz

↔

12.5kHz

↔

16kHz

Press the [

] or [

] button.

F
1
F
2
F
3

F
4
F
5

100

125

160

200

250

315

400

500

630

800

1.0k

1.25k

1.6k

2.0k

2.5k

3.15k

4.0k

5.0k

6.3k

8.0k

10k

12.5k

16k

100

125

160

200

250

315

400

500

630

800

1.0k

1.25k

1.6k

2.0k

2.5k

3.15k

4.0k

5.0k

6.3k

8.0k

10k

12.5k

16k

Rear Group

Front Group

Press the [6] button to select the
Q curve pattern.

Repeat the operations in steps

to change the settings

for each band.

Hold down a button, [1] to [5], for
more than two seconds to preset
a value.

SLOW

MIDDLE SLOW

NORMAL

MIDDLE SHARP

SHARP

Содержание CD 8445E






































































































Результаты поиска

Содержание CD 8445E

Отзывы:

Бренды по названию

Популярные бренды

Eclipse CD 8445E, Руководство пользователя

Результаты поиска

Содержание CD 8445E

Отзывы:

Бренды по названию

Популярные бренды