manualshive.com logo in svg

Eclipse CD 8445E, Руководство пользователя

Поделиться
Скачать
Eclipse CD 8445E Скачать руководство пользователя страница 48

„

 160 

„

Various Settings

ESN security operating procedure

This deck is equipped with ESN (Eclipse Security Network). A pre-registered music CD (Key CD), four-
digit security code, or a Memory Stick on which all unit functions will not operate, even by turning the
ignition switch to the ACC or ON position or reconnecting the battery after turning the ignition switch off
or disconnecting the battery during maintenance. 
ESN can be set or cancelled using any of the following methods:

Key CD security (See page 161)

You can record a specific CD that you have as a "Key CD" with the deck, and this CD can then
be used to set and cancel the security settings.

Memory Stick security (See page 164)

You can record a Memory Stick and a secret code (security code) with the deck, and this
Memory Stick or secret code (security code) can then be matched with the deck to set and
cancel the security settings.

ACC security (See page 168)

This method can only be used when Memory Stick security has already been set. When ACC
security is set, button operations are disabled when the ignition switch is turned to OFF and
then back to ACC.

About ESN

Содержание CD 8445E






































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды