Eclipse CD 8445E Скачать руководство пользователя страница 58

Страница: 58 / 101

170

Various Settings

How to operate the AUDIO CONTROL

Turn to the right:Increases the
volume.
Turn to the left:Decreases the
volume.

ATTENTION

Press the [MUTE] button for less than one
second to cut the volume or restore it
instantly.

The loudness control may be turned on to
emphasize low and high frequencies at low
volume levels.
Loudness compensates for the apparent
weakness of low and high frequencies at low
volume by boosting the bass and treble levels.

ATTENTION

• You can cancel the loudness

function by pressing the [AUDIO
CONTROL] button for longer than
one second while the loudness
function is ON.

• Loudness control is not available

when CSII is ON. In order to
enable loudness control, turn OFF
CSII. (For details on turning CSII
ON/OFF, see page 173.)

Adjusting audio volume

Turn the [AUDIO CONTROL]
button to the left or right.

WARNING

Do not adjust the volume or other controls
while driving the vehicle. Do so only while
parked in a safe location.

Enabling the loudness
control

Press the [AUDIO CONTROL]
button for longer than one
second; [LOUD ON] will be
displayed on the screen.

Содержание CD 8445E






































































































Результаты поиска

Содержание CD 8445E

Отзывы:

Бренды по названию

Популярные бренды

Eclipse CD 8445E, Руководство пользователя

Результаты поиска

Содержание CD 8445E

Отзывы:

Бренды по названию

Популярные бренды