Eclipse CD 8445E Скачать руководство пользователя страница 67

Страница: 67 / 101

How to operate the Sound Adjustment Mode

179

Parametric equaliser adjustment
(PEQ)

The parametric equaliser adjusts 7 frequency
bands.

The mode will change to parametric
equaliser adjustment mode.

Each time the button is pressed, the
selection changes in the following
order.

➔

www

When the button is turned, the
frequency changes in the following
order.
1: 63Hz

↔

80Hz

↔

100Hz

2: 125Hz

↔

160Hz

↔

200Hz

3: 250Hz

↔

315Hz

↔

400Hz

↔

500Hz

4: 630Hz

↔

800Hz

↔

1kHz

↔

1.25kHz

5: 1.6kHz

↔

2kHz

↔

2.5kHz

↔

3.15kHz

6: 4kHz

↔

5kHz

↔

6.3kHz

↔

8kHz

7: 10kHz

↔

12.5kHz

↔

16kHz

This adjusts the frequency level.

[ ] button:

Increases level.

[ ] button:

Decreases level.

Each time the button is pressed, the
Q curve changes in the following
order.

The preset value is overwritten by
the value set using the above steps.
The time alignment and crossover
adjustments will also be stored at this
time.

At this time, other adjustments can
also be made in normal mode.

Turn the [SEL] button to select
PEQ.

Press the [SEL] button.

Press the [SEL] button to select
the band to be adjusted.

Turn the [SEL] button to select
the frequency to be adjusted.

Press the [

] or [

] button.

Press the [6] button to select the
Q curve pattern.

Repeat the operations in steps

to change the settings

for each band.

Hold down a button, [1] to [5], for
more than two seconds to preset
a value.

Press the [RTN] button.

Press the [SOUND] or [RTN]
button to exit sound adjustment
mode.

NORMAL

SHARP

SLOW

XII

Содержание CD 8445E






































































































Результаты поиска

Содержание CD 8445E

Отзывы:

Бренды по названию

Популярные бренды

Eclipse CD 8445E, Руководство пользователя

Результаты поиска

Содержание CD 8445E

Отзывы:

Бренды по названию

Популярные бренды