Echo CS-4010 Скачать руководство пользователя

Страница: 9 / 60

CS-4010

SAFETY

X7503380000

7/22 ECHO Incorporated

Users of this product risk injury to themselves and others if the
unit is used improperly and/or safety precautions are not
followed. Proper clothing and safety gear must be worn when
operating unit.

Physical Condition

Your judgment and physical dexterity may not be good:

• If you are tired or sick

• If you are taking medication

• If you have taken alcohol or drugs

Operate unit only if you are physically and mentally well.

Eye Protection

◆

Eye protection that meets ANSI Z87.1 or CE requirements
must be worn whenever you operate the unit.

◆

For additional safety, a full-face shield can be worn over
safety glasses or goggles to provide protection from sharp
branches or flying debris.

Hand Protection

Wear sturdy, no-slip, rubber work gloves to improve your grip on the

handles. Gloves also provide protection against cuts and scratches, cold

environments, and reduce the transmission of machine vibration to your

hands.

Hearing and Ear Protection

ECHO recommends wearing personal protective equipment whenever unit

is used.

Breathing Protection

Operators who are sensitive to dust or other common airborne allergens

may need to wear a dust mask to prevent inhaling these materials while

operating unit. Dust masks can provide protection against dust, plant debris,

and other plant matter such as pollen. Make sure the mask does not impair

your vision, and replace the mask as needed to prevent air restrictions.

Содержание CS-4010





























































Результаты поиска

Содержание CS-4010

Отзывы:

Похожие инструкции для CS-4010

Бренды по названию

Популярные бренды

Echo CS-4010, Руководство оператора

Результаты поиска

Содержание CS-4010

Отзывы:

Похожие инструкции для CS-4010

Бренды по названию

Популярные бренды