Echo CS-4010 Скачать руководство пользователя

Страница: 40 / 60

OPERATION

CS-4010

X7503380000

7/22 ECHO Incorporated

Bucking

Bucking is the sawing of a log or

fallen tree into smaller pieces. There

are a few basic rules which apply to

all bucking operations.

• Keep both hands on the handles

at all times.

• Support logs if possible.

• When cutting on a slope or

hillside, always stand uphill.

Keep in mind that the wood is heavy and that it will bend and pinch the saw

if improperly supported. The trunk will weaken at the point where you make

the cut unless the tree is lying on perfectly flat ground or supported as

shown. If you make the cut with the tree on the ground, don’t let the saw’s

chain dig into the earth; it is harmful for the saw, and you stand a good

chance of being struck by flying debris.

To cut the trunk, use the bucking and two-cut sequence shown. The first cut

should be no deeper than one-third the trunk diameter.

Chain And Guide Bar Combination

The following combinations are recommended for model CS-4010.

Use of replacement saw chain and/or guide bar other than that
specified, or operation without the optional Kick Guard

place, may cause severe kickback resulting in serious injury.

Guide Bar

Saw Chain

Length mm (in.)

ECHO Part No.

Pitch mm (in.)

Type

Links

Low-kickback

406 (16)

16A0CD3757

9.53 (3/8)

91PX-57E

457 (18)

18A0CD3762

9.53 (3/8)

91PX-62

Support

Finish cut

Uphill Position

First cut

Содержание CS-4010





























































Результаты поиска

Содержание CS-4010

Отзывы:

Похожие инструкции для CS-4010

Бренды по названию

Популярные бренды

Echo CS-4010, Руководство оператора

Результаты поиска

Содержание CS-4010

Отзывы:

Похожие инструкции для CS-4010

Бренды по названию

Популярные бренды