Echo CS-4010 Скачать руководство пользователя | Manualshive

Страница: 33 / 60

background image

CS-4010

OPERATION

X7503380000

33

7/22 ECHO Incorporated

◆

After starting engine, immediately squeeze and then
release throttle trigger to release fast idle throttle latch,
otherwise severe brake damage may occur.

◆

Never use fast idle throttle latch for cutting.

◆

Use fast idle throttle latch only in starting.

Note: Do not increase engine speed while chain brake is locked.

Severe brake damage will result.

Starting Warm Engine

Make sure bar and chain are free from any obstruction when
starting the chain saw.

1.

Move chain brake lever fully

FORWARD to LOCK chain brake

before starting.

2.

Confirm there is fuel and chain

oil in tanks.

3.

Securely hold chainsaw as

shown and pull starter handle.

4.

Choke (A) may be used if

necessary, but after first starting

sound, squeeze throttle trigger to

release choke to OPEN and

return engine to idle.

Note: If engine does not start

after 5 pulls, use cold start

procedure.

Chain Brake Locked

A

«
...
31
32
33
34
35
...
»

Содержание CS-4010





























































Отзывы:

Нет отзывов

Похожие инструкции для CS-4010

Бренд: P.I.T. Страницы: 29

Бренд: P.I.T. Страницы: 32

Бренд: McCulloch Страницы: 20

Бренд: Worx Страницы: 24

Бренд: Worx Страницы: 52

Бренд: Echo Страницы: 48

Quickvent QV-8000 Type 1

Бренд: Echo Страницы: 30

Бренд: Echo Страницы: 370

Бренд: MTM Страницы: 36

CNS 18-30 Battery

Бренд: Kärcher Страницы: 356

Бренд: ICS Страницы: 7

Бренд: Husqvarna Страницы: 88

Бренд: McCulloch Страницы: 34

Inline 5258669-01

Бренд: McCulloch Страницы: 256

Бренд: SMASH Страницы: 76

Бренд: Kraissmann Страницы: 28

Бренд: Kraissmann Страницы: 28

Бренд: Jonsered Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды